Step furnace construction technology for gazebos with their hands

gather with friends in a cozy gazebo and enjoy the fresh, juicy kebabs - the best of the day and you can imagine the scenario!To this pastime was more comfortable, you can build a gazebo right in the oven, which fry barbecue and views to enjoy the open fire will enable, without confusing your guests smoke.

What you need to build a furnace in the gazebo?

Firstly, we need a gazebo itself sufficient area, about an arbor made of polycarbonate read here.Paul to install the furnace in the gazebo should be on a solid foundation, if it is not, you will need to remove the coating from the part where the oven, and make concrete pouring will stand.Also, you will need full-bodied red refractory brick, mortar for masonry, sheet metal for exhaust pipes and devices.The pipe can be bought ready-made and complete it headroom, which will protect it from rain and snow.

addition, will need a metal sheet with a thickness of 3 mm for the production of charcoal pan, grill barbecue, tile or granite tiles for floors and countertop ready, sawn to size.Pre-buy two types of sealant - resistant sealing and exhaust pipes and water-resistant silicone for countertops.

device foundation

Foundation dimensions are determined by the size of the furnace.For oven-barbecue with worktop enough to make the size of the foundation 1,5h2 meters.At this size dig a hole depth of 30 cm line the bottom and covered with a layer of coarse sand, which must be watered with water, and thoroughly compacted.Doing this you can end the log side.Along the perimeter of the formwork set of boards 20 cm wide, fastening them to the screws.

Formwork installed in a pit on the construction level, laid reinforcing mesh and concrete is poured.Concrete can be bought ready-made or make yourself from cement, sand, gravel and water in a ratio of 1: 4: 4: 4.The valve must be completely drowned in the concrete, and the solution is to "break" - to pierce in several places to remove air, and then align the mirror.Concrete Curing lasts from one to three weeks.

masonry oven

furnace Laying lead in a half-brick, that is, the thickness of its walls is equal to the width of the bricks.To smoothly put the first row, you need to start laying the stove mark the outline of the future with the help of stretched cords - it is convenient to attach to the valve, stuck into the ground outside the formwork.Align the oven must be at the rear of the casing to the front there is a place that would later need to be tiled.This will create an additional fire safety.

A solution according to any of the recipes:

• red clay, sand and cement in a ratio of 2: 3: 1;
• cement, sand, glue for granite in the proportion of 5: 7: 2.

clay to prepare the solution should be soaked in water for 1-2 days, then mix thoroughly, remove foreign objects, mixed with sand and in the last instance with cement.

solution with the adhesive for porcelain tiles are prepared as ordinary cement: all the dry ingredients are mixed together and topped up with water to the desired consistency.The solution should not run with a trowel and move out with him at an inclination of approximately 45 degrees.

Masonry are in the form of the letter "W", one of the resulting sections will serve as a furnace, and the other - the desktop.The solution is placed on the casing along a stretched cord, level, spread on top of brick, check it is horizontal with a spirit level and a little rap hammer.When laying the next brick solution is applied and on its end part for better grip with the last brick.

second row start with a brick, cut in half - it will create a stretcher bandage.Cut the brick can use grinder or chop it with a pick.This process requires some skill, but it is not as complicated as it may seem.Brick first rattle gently in place on both sides of the split, and then using the firing straight into the center of split it in two, chipped polish.

seventh, eighth and ninth rows are placed again in the usual way.Tenth - under the scheme of the sixth, creating another ledge.Again, three rows of conventional masonry and fourteenth - with ridges.Fifteenth series completes the half of the furnace, which is reserved for the table.

Half BBQ continue putting, alternating between odd and even numbers.The height of the masonry should provide comfort, but do not make it too high - will not pull.In order to make the furnace roof, operate with another number of protrusion.On the ledge in front of the arch fix the two metal brackets at a distance of 25 cm - they will be laid torchkovy number forming the front arch of the furnace.For the posterior fornix only one corner at a distance of 13 cm from the rear wall.Posterior fornix are placed as torchkovoy masonry, brick Based on previous row and corner.

table decoration

countertops easier to order a finished size.It is placed on the upper range of desktop speaker, be sure to carefully promazyvaya joints with silicone sealant.The tabletop can be set washing or just use it as a desktop.

You can make your own countertop.For this purpose, the protruding rows of bricks put the right size stove, plastered with cement mortar, and its top trim tile, granite or decorative stone.This countertop is not afraid of no water, no cold or hot dishes.

pan of coals and grill

tray welded sheet metal.The dimensions must correspond to the inner area of ​​the furnace wall height - from 10 to 15 cm The front of the tray to make better perforated for better air convection..Removable drip tray for easier cleaning and tidying.Install it on the lowest ledge.You will be two free projection.On average projection set grill for a barbecue or barbecue, and the top is used to set the smokehouse.

Exhaust pipe and

hoods, as well as a pipe, you can buy ready-made or make it yourself from sheet metal by welding or riveting.The stretching can be colored heat resistant paint.The gaps between the oven and extractor fan is necessary to process the heat-resistant sealant.

pipe through the ceiling and roof of the gazebo is passed through tunneling fireproof, insulated non-combustible material.On the tube, wear headroom.This element is necessary not only for beauty and protection from the rain, but also to create proper traction.

finishing

Paul before the stove should be put fireproof and non-slip material, such as granite.For laying porcelain tiles need a special glue, which is sold as a dry mix.Samu stove can be left undecorated, only to walk on the surface of the sander to remove the remnants of the solution, then rinse with a stiff brush.You can decorate it with decorative stone or brick, giving it the desired shape and completing the interior of your pergola.

can build more sophisticated oven, a cooking stove or a fireplace, a work desk, a sink and counter tops made of natural stone.Creative imagination, and your pergola will be a welcome place of rest for your guests!

Also, you might want to read about: arbor from a bar with your hands, a gazebo made of plastic bottles, and even read about a hexagonal gazebo with their hands