Sticking wallpaper in the corners

Wallpapers are one of the most accessible materials for finishingnot even very high-quality and smooth walls.They are perfect spots to hide irregularities and even distortions.But glue them on a very curved surface is not easy inconvenient, sometimes even impossible.Therefore, the first step is to align as much as possible all areas of the wall, and the corners should be given the most attention.If other areas of the canvas walls of wallpaper glue impregnation acquired elasticity and could stretch the curves on the corners, both internal and external surprises are not excluded in the form of distortions and large folds.

Even on a perfectly smooth corners sometimes there are difficulties.Therefore, before starting work should be well prepared for the question, "How pokleit wallpaper in the corners?".

From start to glue?

Many people recommend the window, and some of the doors.In reality there is no difference if you do not take into account past trends, when the wallpaper had a special edge to overlap.Because of what they had to be glued with an overlap of not less than 1 cm. In this case, the best option was sticking it on the far wall with a window.Since it was not visible seams at the entrance to the premises.Today, wallpaper manufactured without this edge, and glue them back to back is recommended.Wallpapering in the corners is not different from the flat spaces.

first step is to decide what are the wallpaper and glue as required for their impregnation:

• Paper require moderate soaking and pre-greasing wall.
• Vinyl require a good soaking, especially when gluing them in the corners, because they are quite thick and dense.
• wallpaper on non-woven basis only require impregnation of the wall.

applied tools for wallpapering

Often drawing on the wallpaper is applied, which is resistant to mechanical damage.Therefore, a special rubber roller or a brush is needed for their smooth.

finishing interior angles

dealt with the types of fabrics and amount of glue can start to work.If the wallpaper started stick from the corner, the mandatory level with a long metal ruler and marking must be applied in a vertical line.It should be so that when gluing a sheet lay down with bloat at an angle of 2-3 cm. The inner angle is less noticeable, so if there is a small overlap and form, it will not be very noticeable.

Widget from SocialMart

When gluing fabric edge of the sheet turned out not straight, it can be cut with the help of wallpaper or installation knife.At the same time after each cut is recommended to break off the blade.Otherwise, the next time they use will occur bully and tears.

Corner is a place where the most prone to peeling wallpaper on the walls.Therefore we should not here to feel sorry for the adhesive, the best option will be pre-impregnation of the surface in several layers.

For reliable sizing angles use a special glue.Excellent suitable PVA glue.

Wallpapering on the outer corners

Rules pasting wallpaper on external corners are a perfect fit in the canvas.There will not pass an option to overlap, because it will be clearly visible.The best option would be "cutting."But that you arrange the outer corner, it should be possible to align the surface using putty.

Next, recommended to lubricate the surface of the wall with glue in several layers.If necessary, use a brush, because it is often impossible to roll to penetrate into small cracks.Pre-impregnated fabric is glued on the bend angle with the second wall of 2-3 cm. In this case, almost always form an uneven edge of the sheet.This is due to the geometry of the walls, and they are not perfect.The second sheet of wallpaper glued to overlap the previous one in 5-8 cm. This is necessary for him to can comfortably take in removing.

then with a plumb, and it is better to use a long level, produced a cut both webs mounting a new blade knife.

It is not worth saving, because when the blades become dulled on the surface may be formed teaser that will be very unattractive.

After the incision once a piece is removed, and gently come unstuck edge docked sheets.From under it removed the rest of the cut, and wallpapers are glued in place.adhesive can be added if necessary.

finishing angles

corners Finishing after wallpapering is seaming joints using a rubber roller and leveling special spatula.They can also gently flatten the wallpaper on the external and internal corners.Here, the important thing is not to overdo it, because you can easily damage the wallpaper at pressing tool.
httpsv: //
This video will help you understand all the nuances of the implementation of wallpapering in the corners.