How to cook the furnace for a bath from pipe

Simple yet efficient furnace for a bath can be made independently of the usual metal pipe with a diameter of 0.5-0.6 m. For a furnace needs a minimum of time and material, at the same time it is able to heat a bath of up to 20 cubic meters.The furnace for the bath of the pipe is the most simple design and can be vertical or horizontal design.The advantages of such ovens may include at least welds, and thus improved reliability, since most furnace burn through in places namely welding.

Recommended wall thickness - 8 mm and more.In addition you will need a sheet metal pipe, chimney with a diameter of 120-150 mm, cutting rebar as well as welding machine and Bulgarian.

vertical furnace tube from

need for such a stove pipe segments 0.9-1 m long and 0.5-0.6 m. The implementation of the vertical furnace technology of the pipe is quite simple.

1. Prepare the formwork for the foundation.The width of the casing is equal to the diameter of the pipe plus 0.5 m. Lay rebar and pour concrete.The thickness of the foundation should get at least 20 cm. After hardening concrete floor spread with bricks or paving slabs.
2. Line the bottom edge of the long section of the pipe - this will be the base of the furnace, and it should be smooth.Carve on the one hand the ash-pit with dimensions 5x20 cm. At the same time ash pit will act as the ash.
3. Over podduvalom fastened by welding the bottom of the firebox.For this cut from the sheet metal thickness of not less than 12 mm diameter circle on the tube is cut at its center an opening for the grate.Grate can be purchased at the store or make your own, is welded to a steel rod cut hole in a grid, leaving gaps equal to the diameter of the rod.
4. cut window for the furnace size of 25x30 cm, the distance from the bottom of the firebox -. 5 cm is welded hinges and fix the door on it.If there is a need to make the furnace in the next room, you can also weld rectangular apron around the door, stepping back from her 5- 10 cm on all sides.
5. Above the firebox perform cutter - a rectangular metal plate with cut corners, for which the sheet is welded to the pipe.The parties clipper and pipe clearances are sufficient for the passage of smoke.Thus, a circulation of the fume flow along the walls, which contributes to heating.
6. at 5-10 cm above the clipper to the walls of the tube is welded grid of metal rods with a diameter of 12-16 mm.This will be the bottom of the heater.The door heater is positioned so that it was easy to open from the steam.The door is performed similarly to the furnace.
7. Top heater brewed metal sheet with a hole with a diameter equal to the diameter of the chimney.At the upper edge of the heater can weld stops to tank if the tank is removable.
8. water tank can be made from cutting a pipe or stainless steel.The bottom of the tank should be repeated exactly top of the stove.By the bottom of the welded pipe -. It must pass through the center of the tank and out of its upper reaches 20-30 cm The top of the tank equipped with a removable cover in the form of a semicircle.In the lower part of the crane crashed.The tank is mounted on the stove and welded.

horizontal tube furnace of

horizontal furnace operate with an external heater and a half tank.Horizontal furnace is compact, as well as increased depth of the furnace, which allows quickly to heat bath.The door of the furnace can be taken in the dressing room - it will create additional comfort when kindling baths.

horizontal stove manufacturing technology:

1. Cut a piece of pipe with a diameter of 0.5 m and a length of 0.8 m Align edge..
2. Make grate area: from sheet metal 10-12 mm thick cut out a rectangle with dimensions 40x80 cm, cut a hole inside it and it is welded to the valve or the bar, or set the grate industrial production.
3. welded grate area inside the pipe.At the same time set the furnace body so that the weld seam of the pipe was under the grate - as iron burns more often in the field of welding, using this technique reduces the thermal load on the joint.
4. Perform stove façade of sheet metal.The shape of the facade -. a rectangle with rounded top, with a width of 60 cm and a height of 70 cm in the facade is cut two rectangular holes - to the door of the furnace and ash.
5. Perform the back of the stove in the form of a rectangle of sheet metal with the dimensions 70x90 mm.The upper part of the rear wall will serve as a heater limiter.
6. welded front and rear of the stove to the oven housing.In the middle part of the front stopper is welded stove, echoing the contours of the rear wall of the top and bottom of the stove body.
7. top of the body, in the back of the hole cut to the size of 15x15 cm above it establishes a set of stove made of sheet metal with a hole for the chimney, the hole should be located closer to the front of 10-15 cm. - Thus creating a flame cut-off, the conditions forcomplete post-combustion fuel.
8. welded to the body of the chimney.The Code will also serve as the bottom of the heater.To increase the volume of the heater on top of its walls is welded grid of reinforcement rod or the height of 15-20 cm.
9. hang the door of the furnace and ash pit.Stove treated with a grinding wheel to remove traces of scale, rust.After the treatment, it can be covered with a heat-resistant polymer and paint is to heat the bath room to paint baking.
10. Install the oven on a base of concrete, or laid in a single layer of brick, granite, paving slabs.Chimneys bring to the street through the roof in compliance with all fire safety regulations: penetration through the ceiling must be carried out with the help of insulation from non-combustible materials, and pipe that goes through the cold attic should be insulated, otherwise it will produce condensation and harmful to the carbonic acid metal.
11. On the back of the stove installed water tank.To install the shelf weld, corresponding to the dimensions of the tank bottom.The heater is placed stones at the same time comply with the rule that the flat part of the stones should be possible to adhere to metal surfaces to make them more warm.

Decrease hard infrared

Metal furnace for the bath, despite the many advantages, have one drawback - they create too rigid infrared radiation, causing the air in the bathIt warms unevenly.Rectify the situation will help masonry around the stove.Running it close to the stove or at a distance of 5-15 cm, providing air circulation along the walls of the furnace, and in addition performs a protective role - touch to the heated brick can cause serious burns, while a red-hot stove is very dangerous.In the lower ranks of masonry make two or three holes for the inflow of cold air, heated by the convection of the laws goes upstairs.About how to impose the metal furnace read on our website.

This method makes it cost-effectively create steam bath light and atmosphere of a real Russian bathhouse.Also we advise to read, how to choose stones for the bath and how to cook pot in a bath with his hands.

Video - steel stove with his hands