Kitchen corner sofa .Step by step instructions manufacturing

Often, the kitchen is not only a place for eating, but also fun.To equip a comfortable and cozy place to help the kitchen sofa.Do not always be the best solution to buy a sofa kitchen corner.You can make your own hands, with minimal effort and expense.The result is a robust, original and created in accordance with the desired size of the kitchen sofa.

often in the kitchen corner sofa factory price, color, size, quality or functionality of the parameters do not meet the buyer.For a small or non-standard kitchen easier and cheaper to make your own sofa.Kitchen corner sofas photos, which can be found on the Internet, will prompt you to model and design.

Tools and materials for the manufacture of kitchen corner sofa

For require materials that can be bought in the nearest hardware store.Small skills in woodworking and the minimum set of tools.

Tools for the manufacture of sofas

1. electric jig saw, planer, screwdriver, drill and sander.
2. hacksaw, pliers, hammer, measuring tape, chisel, carpenter Area, staple gun.

Materials for kitchen angular sofas

1. bar section 40x40 mm about 1350 mm.
2. Bruce 24h25 mm - 3650 mm.
3. Bruce 15x15 mm - 3000 mm.
4. Board 20x40 mm -1000 mm, suitable pine, beech or birch.Plywood
5. 8 - 10 mm thick bottom and side walls - 2 pages.
6. Fiberboard - is used for the back wall - 1 sheet.Footage given approximate and is calculated according to a more detailed drawing.
7. Foam Furniture from 5 cm thick, high density and elasticity or padding polyester.
8. Upholstery: leather, Barkan, nubuck, tapestry, mikrofayber, velor, etc.Pay attention to the upholstery of practicality.The coating should be easy to clean and resistant to chemical agents sanitation.
9. Consumables - Screws (4h80, 4h60, 4x20 mm) SCREW, nageli, hinges, feet, bolts and washers (6 - 8 mm), etc.

need a reliable mechanism for the factory, in the event that if you want to make the kitchen pull-out sofa.

phased framework for the production of corner sofa

First of all, it is made a drawing with exact dimensions and sizes.On the basis of the drawing done calculation necessary materials.The preform prostrugivayut and sanded before marking and sawing.This will keep the dimensional accuracy of the fit of parts of the sofa.The approximate dimensions of the corner of the sofa can be used as a basis:

• maximum height - 855 mm;
• sofas length - 1200h900 mm;
• corner insert - 450h450 mm.

1. By and large, the design of the kitchen corner sofa with his hands is not big problems.The main carrier part is a sidewall, which carry most of the load.They are made from a single sheet of plywood or thick cohesive joiner's board.The markup is applied marker or pencil and cut jigsaw.
2. Collect of timber 40x40 mm frame for two long and short sofas.Frames are made in the form of parallelepipeds and are attached to the lateral planes.Angular connections zapilivaem on spike and mustache, then sit on the glue.Rallies L and T - junctions are set strictly at 90 °.
3. Corner connections can be through in polbrusa, single spike or two - three spikes through or hidden in sweat.For bond strength reinforced metal area on the screws or dowels.The frame is collected in conjunction with backrest and bolted to the sidewalls.
4. get the basics of the kitchen corner sofa, folding seats are going to cover.They may be solid for long and short sofa or divided into sections.From timber 25x25 mm rectangular frames going down and sutured 10 mm plywood.Ready oshkurivayutsya seat, covered with stain and varnish, glued to the foam plane and tighten upholstery.By the long side seat screwed piano hinges.Installation of flaps - seat performed at the final stage of work.
5. smallest corner unit is going the same way.From timber (40x40 mm) frame is made triangular with sides of 90 ° and 45 °.Module upholstered plywood or laminated fiberboard.

Assembling corner sofa modules for kitchen

collected blocks of two sofas and corner module carefully oshkurivayutsya.Places chips or other damage occurred during smeared putty for wood.Wooden elements, which will not be covered with upholstery - are covered by stain and varnish.Lac housing corner sofa to the kitchen opened at least three times.

1. dried out parts are put on little feet and rallying.Feet can be purchased in the shop of furniture accessories, and they are fastened with screws to the supporting frame of the sofa.It must be at least eight feet for the entire corner of the sofa.
2. Structural elements are exposed and by adjusting the leveling feet.Correctness of installation is checked with a spirit level.The marked locations are drilled holes for attachment bolts with a diameter of 6 or 8 mm.Washer for bolts purchased from a wide field.For each of the fastening bolts will need two goals.A washer is placed underneath the bolt head and by the second nut.
3. installing fixing bolts, take care of the free access to them.After some time, the bolts will squeeze timber, and they will need to pull up.When moving, moving, or for thorough cleaning also require disassembly of the sofa.

upholstery and trim the corner of the sofa to the kitchen

Upholstery kitchen corner sofa is chosen based on its operation in the vicinity of the cooker and sink.It should be easily cleaned of grease and food vapor deposited at the same time showing resistance to chemical cleaners.

1. For soft sofas used furniture elastic foam 5 cm thick.For semi-soft - sinteponovye packing.On the back of the sofa covered with a thin layer of glue at the junction of foam or padding polyester and packing tightly to the back plane.
2. Of Molds cut upholstery fabric for upholstery patterns and size details.Furniture upholstery stapler clips on the back plane of the back of the docking place in the seat and backrest.The material is pulled tight and secured at the corners.Then stapled over the entire length, including the sides.
3. From bar 40x40 mm armrests are made.Throughout the length of the timber is grooving sample depth of 20 - 30 mm.The width of the sample is determined by the thickness of the side wall.The blank is fitted by the filler and upholstery fabric.Then armrests are coated with glue in the grooves, and sit on the sidewall.You can additionally secure the screws armrests.