Warming bath roof

technology grazing roof insulation bath

grazing insulation is used most often in small wooden baths.Thick board cut one into the upper crowns log 5-10 cm. The thickness of the boards should be at least 60 mm, since they play a role at the same time bearing ceilings and insulation.Below, you can sheathe their insulation and decorative cladding, and the top - in addition to warm.

1. grazing the ceiling boards are placed across the steam room.To improve the thermal insulation properties of the ceiling in the penultimate crown perform dredging thickness boards.The logs are processed antiseptic for interior work, after which the board is laid, tightly fitting them to each other.For better tightness can use decking.
   

   laying planks on the ceiling

2. Inside the board is treated with an antiseptic, dried, and then sheathe vapor barrier film, fixing it with the building or the furniture stapler.Joints glued metallic tape.
   

   ceiling glued vapor barrier film and a metal tape glued

3. the top board is closed vapor-permeable waterproofing.Water vapor permeability is required in order to drain the water vapor trapped in the covering board, otherwise they will start to rot.It is therefore not recommended to use plastic wrap to waterproof ceiling.On top of the waterproofing layer is laid insulation material.This may be a clay mixed with sand or sawdust, expanded clay, slag, as well as modern fiber materials.A layer of expanded clay or clay in this case must be at least 20 cm.
   

   top of the board is poured concrete block

4. mineral or basalt wool, has excellent insulating properties, put a layer of 10 cm. For laying insulation in a bath with an atticfloor must first be put on the floor bars playing a support role for the finished floor.Step styling -. 50 cm bars need to carefully handle disinfectant.
   

   laying mineral wool insulation for

5. top of a heater put another layer of waterproofing.Fasten it to the bars finished floor stapler.This layer of waterproofing is necessary to protect the insulation layer from leaks or kapelkondensata.On top lay a waterproofing finishing floor attic floor, for the unheated attic enough to lay a waterproofing unplaned board to protect it from damage.

technology boarded roof insulation bath

This method differs from the grazing that overlap run above and below the ceiling beams that hold the walls.Such overlap can be used for any size baths, a wood and brick and block.The main insulation in this case, are placed in the space between the ceiling beamed blister.

technology boarded roof insulation bath

1. Perform rough ceiling board thickness not less than 25 mm, fixing it from the bottom of beams with nails or screws.From the rough ceiling sheathe steam vapor barrier metallized film with a stapler, a film glued joints with duct tape.Perform finishing ceiling linings, fixing it on the bars, stacked on top of the vapor barrier.All wooden elements must be treated with antiseptic and linings - special varnish for bath water based.
   

   Lay vapor barrier sheets are impregnated with antiseptic and placed battens

2. between the joists are placed for insulating mats made of mineral fiber materials.Layer thickness -. 10-15 cm mats placed so that no gaps remain.Instead, you can use concrete block mats.The clay or slag in this case is not recommended, as they create quite a lot of pressure on podshivnoy ceiling and can push the board.
   

   process of laying of insulation mats

3. top of the insulation film to put a waterproof vapor-permeable layer for vapor removal of a layer of insulation.The joints of the film are also glued shut.
   

   Laying waterproofing film

4. beams lay on the finishing floor attic floor.It can be made of boards or waterproof plywood.

Insulation of roof slopes

Warming rays is necessary only if the device heated attic.In general roof insulation bath technology is not different from the conventional roof insulation using fibrous materials or foam.Thermal insulation can be made both during laying of roofing materials, as well as later.To perform thermal insulation arrange a kind of "pie" consisting of a vapor barrier on the part of the attic, waterproofing from the roofing and insulation layer between them.