Washer erases long : erases too long , longer than expected

washing process in the washing machine can take anywhere from an hour to two hours or more.Duration of washing depends on the selected program.Therefore, if you show that this time the laundry is washed more than usual, first of all, make sure that you are running a standard program that does not involve pre-soaking and rinsing reusable.

Given a normal wash program, but it lasts longer allotted time, most likely, there is a malfunction of the washing machine.In this article, we will tell you about the possible causes of the increase of washing time and that can be done to solve the problem on their own.

Difficult ingress of water into the tank. water can flow into the washing machine slowly or intermittently for a variety of reasons.This is due both to the state of the water pipes (for example, sometimes the fault of the whole becomes weak water pressure or a blockage in the pipes) as well as with the device itself.Thus, the normal water supply to the tank may interfere formed blockages in the inlet hose or in the filter.

found it difficult to drain water from the tank. This problem is the exact opposite of the first, but the effect of producing the same.If the tank water remains constant, the machine can not switch to the spinning mode, resulting in prolonged washing.Normal drain water often prevent blockages in the drain system.They typically arise due to contact with the drain hose and filter foreign objects, clusters of detergent residues and dirt deposits.

There is a permanent set and draining. In this case, the laundry may continue indefinitely, so the washing machine can not be fixed in the tank water level required to start the wash.A similar problem can occur for two reasons.First - it is the mistakes made when installing the unit to the sewer pipe.The second - a failure or incorrect operation of the water level sensor.

water in the tank is not heated. To start the set wash program is necessary to keep the water in the tank warmed to the desired temperature.If heating does not occur, or it is very slow, prolonged washing.During the heating and temperature control of water in the tank corresponds to two devices - a heating element and a thermostat (temperature sensor).Failure of one of them leads to the fact that the temperature and wash cycle is broken there is a malfunction of the washing machine.

drum rotates without stopping or, conversely, fades. Such failure may also lead to the fact that the washing lasts very long.The most important reason that causes a similar problem - a failure of the electronic control unit.Less serious reason, which is much easier to remove - an overloaded drum.

• Weak water pressure. Check the pressure in the pipes can be simply assessed the pressure coming from the tap with cold water.If he is not strong enough, contact the housing office.
• clogged inlet hose or filter. Eliminate blockage can by removing the inlet hose and blowing through it.If the pollution is serious, rinse under running water hose.A blocked filter is cleaned with a toothbrush and is rinsed with warm water.
• clogged drain hose or valve. It is necessary to act in the same way as in the previous case.
• connection error. Check the drain hose to the sewer installation.The connection must be made not directly, but through a special trap, which by the standards should be placed at a height of not less than half a meter.
• Faulty pressure switch. water temperature sensor can be checked for serviceability with a small length of flexible hose with an appropriate cross-section.One end of the hose, attach to the pressure switch, then attach the device to your ear and blow at the other end of the hose.If you hear clicks, faulty pressure switch, otherwise it will have to be replaced.
• Broken PETN. most common cause of problems PETN becomes thick layer of scale, which hinders its normal operation.Scale is easily removed with a solution of citric acid.However, if after cleaning, the appliance does not "come to himself", then it is defective and needs to be replaced.

Faulty thermostat. water temperature sensor rarely fails, but if it is, all the same happens, the best solution would be to buy a new device, rather than spending time and money to repair the old.

Faulty control unit. Malfunction of the unit is considered to be the most serious problem, since it is difficult to handle on their own.Usually, a broken unit is given to re-flash or replaced with a new one.

drum overloaded. sometimes fails when washing, when the drum is loaded too many clothes.In this case, you must force quit the washing program, drain the water and remove the excess items.

• may set or draining difficult, because there was an excess of one of the hoses.This problem is easily removable, so before you begin to diagnose the problem, make sure that the drain and filler hoses are not deformed.
• Make sure that in different parts of the washing machine is not formed blockages.Use only high quality detergent and do not exceed the recommended dosage.Before washing, check the pockets of clothes, fasten zippers.Things with lots of decorations wash in special covers.
• Periodically prevention of occurrence of scum and limescale.You can use not only a means for commerce, but also popular, such as vinegar or citric acid.