The peculiar way of " saving " power

Getting

What beneficial for themselves the rules you must follow?

controller can not enter the apartment without your permission.But if you refuse him, he could not make an act of tolerance, which "will contribute" then that you shut off gas, electricity and water because of this.This act, you will need to sign and get out in any way, it is better to let.A light and gas turn off, in fact, they have no legal rights if:

• As Energonadzor records - there is a dangerous condition for the sustenance of human beings and animals.
• subscriber, ie, you have to document the established debt.
• your meter is not registered, and it threatens unmetered consumption.

If you have been to blame failure in this reviewer asked, he must be removed from the meter, seal the package, but leave it at the party, so he took it to them for examination.A subscriber, in turn, assures that the process in the relevant document.

those counters that are located in a common area of ​​the stairwell, are the responsibility of utilities.

Before you crack the seal, it is necessary to accumulate debt and died to pay.After a break to unwind, slow down due to the accumulated debt figures.

Here we have come to, to talk about how to carefully remove the seal, but it is worth more to find out how the seal looks at electricity meter according to the type and identify opportunities to quietly remove it.

1. plastic seal in the form of a small disk diameter up to 10 mm.Set this type of seals on whether the wire line and pressed a pair of pliers, so that it was impossible to move it on the line and get to the counter.
   Use these seals for water and electricity meters.At present, rarely used type of seals.Remove the seal there is no difficulty, besides, it's just easy!It makes it very easy.Look for the seal components on the line, they pressed Sundae earlier.That they are not passed to the counter, but the note can be easily untied.If you are doing an autopsy seals the first time, you should put on the line the engine oil, to slide and try to untie and pull off the seal from the fishing line.
   

   

   Suddenly there are any problems, then you must seal succumb to the heat treatment, 80 degrees would be sufficient that the plastic succumbed.In the seal after removing found some holes that will be after the checkpoint fishing line or wire to restore the former appearance.The holes on the seal expanded, and then easily took the line back, you must first play around with string or wire.In order to restore the seal on the current, we need a new fishing line or wire that is stretched across the holes latched.Seals are pressed with pliers, but not so much that you suddenly have been able to pull it off.

   

2. Lead.Another masthead question how carefully remove the seal.The principle of this seal construction at the same as that of the previous one, but the important material, which is made of - lead.Material at squeezing (fillings) are very much sets and of course just to move the seal will not work.But it is very rare, and the units it manages.N Uses electric meter.If you could not pull the seal, try a knife cut the wire or fishing line under the base, which was not at all noticeable.Cropped fishing line when the seal is on the table.It is clamped in a vise and drill holes drilled.Lead is easily drilled.The hole diameter must be done the same as that of the wire.Extend it can also be using it.If the cartridge will not be able to pinch a little bit, you can hold it with sheets of paper.Drill necessarily be qualitatively operable.In the hole is passed a wire, fishing line, etc.Sealing seals.For expansion using the same principle as in the previous embodiment.Clamping seal need with great force, but also so that in the event of re-opening does not need to use a drill again.
   
3. Seals numbered holographic sticker also are among those who can organize their absence.The most used form.There are different quality material.Performed and from different components, adhesive components, etc.To cope with these seals help ordinary three-liter cans, which can organize a partial insulation.The cover is done two holes, through which the following will stretch two rubber hose up to 2 meters in length.Bank is filled with boiling water, but gradually, so as not to burst.Seals close cellophane, so that part of the polyethylene seals hung at the corners.
   
   On one hose seal is induced, and the other of which blow air (hot steam).A layer of adhesive on the seal begins to soften, making it easy to remove it, and then put in place.

These seals - it is definitely not all that exist, but it is with them you will have to face nowadays constantly.Good luck to all!