Folding table with his hands.Step-by-step instruction

Folding table with his hands.Photo

Folding picnic table with his hands.Step by step photos

Before assembling the folding table, you should remember that half the battle is the use of quality materials .Bruce and the board should have as little as possible knots and cracks and delamination of wood are not allowed.In addition to lumber needed fasteners, hinges, tools to protect the lumber from the effects of the atmosphere.

materials required for the manufacture of table

To make a folding table, it is necessary to have on hand:

1. timber size of 45 × 45 mm - 8 pcs.length 730 mm - for the manufacture of the legs;
2. rail 45 × 20 mm 2 h550 mm and 2 x 950 mm - for the assembly of the upper frame podstolya, as well as 2 x 350 mm - for the flip part;
3. plywood slats 40 × 27 mm for the supports - 3 x 450 mm;
4. 18-millimeter plywood dimensions: - 985 × 585 - sheet for countertops - 2 sheets of 985 × 530 for reclining parts - 1 sheet of 885 × 481 mm for the shelves;
5. rail 440 × 40 mm as a cross;
6. slats 2 450 × 40 mm for the side support members;
7. 4 loops 60 × 34 mm for fixing the table covers;
8. 4 loops 80 × 41 mm for folding legs;
9. of galvanized or stainless steel screws;
10. metal dowels for shelf mounting.

Slicing blank, try to angles of all components and their ends were angles .To do this, use a carpenter's square, and in its absence, you can apply a corner of the sheet material cutting factory.

Folding table with his hands drawings.Photo

Assembly instructions

Before assembling a folding table with his hands, it is necessary to prepare parts of the timber for installation.To this end, each frame member is cut to 20 mm groove width and depth of mid preform (22.5 mm).From the edge to the groove, measure the same distance - 30-40 mm.

-step how to make the photo a folding picnic table

After all the slots are sawn, drilled holes for joining parts together and fixing feet.

To avoid skewing the frame in the manufacture of folding table with his hands on each leg make cruciform cuts , in which the installation will frame corners.In more detail, this process can be considered for the following pictures.

properly prepared parts are the key to high quality build, so it is advisable to use high-quality equipment - a good circular saw, drill, set of chisels and other carpentry tools.

Gather upper frame podstolya (common name countertops frame).To do this, the rack is collected in the groove and fixed in upholstery SCREW (screws Allen key);

On collected frame of reference set feet, combining the pieces with sawn rails of the frame.

the corners of the plywood shelves make cuts under support.To fix the plate at a distance of 220 mm from the edge of the set of legs metal dowels .

Gather retractable support elements.For this purpose, the remaining bars are mutually connected strips installed in the slots, fixing place konfirmat compound.

sanded and primed countertop and other details, start staining steps, rails and tabletops.

Mount spacer shelves. side jumper is attached to the frame countertops.The support rails are attached to a shelf, to which holes are drilled in it.Keep in mind that this work requires great care, because even a small bias can affect the geometry of the table.

table mounted to the frame jumper, and then fasten three additional spacers.

Drawer legs on hinges attached to the outer struts.

basic and reclining part countertops bolted to the loops.

table cover is mounted on the frame , then the middle part is fixed to the frame with screws.

collected in accordance with our instructions table will have sufficient strength and reliability.The main thing to do the work in stages, represented by the sequence.Processing and staining necessarily carried out before assembly.Otherwise, carefully paint the individual parts will not work and the finished product will not look elegant and impressive.

table convertible with his hands.Instructions

table sliding type has a solid, stable construction and its assembly will be mastered by even a novice.When folded, the dimensions of the tabletop equals 1 200 × 700 mm.After moving apart the table top, formed in the opening set a special insert to give the length of the table top 1670 mm.This makes it possible to place an additional table for two adults.

Tools and materials

Before going to the construction market note which parts and materials needed for assembly table with sliding cover:

• laminated chipboard 25 mm thick;
• PVC strip for pasting edges up to 2 mm thick;
• aluminum corners measuring 50 × 50 mm - 4 pcs.500 mm;
• telescopic rails for drawers 500 mm - 2 pcs .;
• furniture legs with a diameter greater than 60 mm - 4 pcs.length 710 mm;
• locking latch for the box - 6 pcs .;
• 10mm screws with M4 thread;Furniture
• screws 16 × 20 3 mm × 4 mm.

For this it is necessary to prepare equipment and tools:

• router;
• electric jigsaw with a set of saw blades for plywood and particleboard (fine tooth);
• circular saw;
• electric drill and a set of drills;
• screwdriver or set of screwdrivers;
• hair dryer or iron construction;
• knife wallpaper;
• level bubble;
• clamp;
• measuring tool pencil.

Before you begin cutting the material, make a drawing table in size, or use our proposed design.In this case, the dimensions of the components listed on the cover countertops submitted drawings.

convertible table.Drawings

instructions for the manufacture of folding table

Step 1. Make markup sheet material, after which the cut parts of chipboard worktop - insert size of 700 × 470 mm, as well as the two halves of the table top size of 700 × 470 mm.Avoid chips on the chipboard surface can be using jigsaw with a special nail file with low-profile tooth.In addition, at the place of the cut can be pasted masking tape, which prevents chipping facing layer.

to exactly sawed slab, it is secured by clamps to the bench and put the edge of the level.The tool should be carried out slowly, constantly monitoring the quality of the cut.

Step 2. Facing a router allows a perfectly smooth side surfaces.This tool also work slowly and carefully.

Step 3. ends Pasting of PVC edge worktops.Securing the workpiece clamp and is cut and attached to the side surface of the plate edge.Thereafter, it is heated hair dryer or iron construction and smooth.After solidification of the material protruding edge of the edge of a knife cut wallpapering.

Step 4: Treat all sharp edges and corners of the aluminum parts.

table Making transformer.Photo

Step 5. In the middle of each corner point and measure out 25 mm from each edge.

Step 6. Each side furniture guides applied to the area and mark the places of their fastening.The target point is drilled corners.To prevent the drill slipping on aluminum, perform PUNCHING mounting positions.Corners and guide connecting bolts.

Step 7: The resulting design guides placed on a flat substrate as follows: corners, coupled with internal guides (thin) have inward to each other, and the corners, to which are attached the outer part of the guide (still thicker) - outside.After that, the movable and fixed parts of aluminum drilled 4 holes.

Step 8. Both halves countertops are laid face down on a workbench or other flat surface.Above, at a distance of 80 mm from the sides of the panels installed retractable guides (mobile, thin part inside).In this case the joint between the halves of the table top should fall in the middle of each guide.

Step 9. stationary half telescopic guide is attached to the left half of the table top and mobile - to the right part of it.For this purpose, screws 20 × 4 mm.

Stage 10. Near the sliding system is mounted latches and hinges.

Step 11. In the disclosed snap pushing both sides of the table top and placed additional panel .Thereafter, all the elements of the table top to form a smooth shift without clearance surface.

Step 12. Additional hinge latches mounted on the middle part of the table top.Received allow secure mounting table as disclosed in, and in the assembled state.

Step 13. 20 millimeter screws attached to the table top legs.

Gathering folding table with his hands, be sure to check out the design on strength in the extended and retracted position.Only after the test table can be considered suitable for use and placed on a permanent place.