Homemade metal stove for baths - to create a guide

At the moment, your bath home can complement a variety of furnace designs, but the most popular are wood, metal constructions - the stove-heater.Such ovens have many advantages:

• · heated oven so very quickly - in about 1.5-2 hours later you can begin to bath procedures;
• · Production costs - minimum;
• · life - from 5 to 25 years depending on the welding quality and thickness of the metal;
• · subject to the production technology is no danger of the smoke room, and explosion.

Despite the simplicity sauna ovens, they are not cheap.But if you have the skills to weld the case, then we can make a simple design your own.At the same time it can even be equipped with a tank for hot water.

What better to do a metal stove for baths

need to use black metal thickness of not less than 5 mm (life of approximately 5-7 years) for the independent production of metal-heater stove.Leading manufacturers offer models of steel about 10 mm thick for the combustion chambers, and a little less - for bunkers with rocks and water tanks.

Metal furnace can be made with a square or rectangular cross-section of the sheet metal, but it means an extra weld and difficult operation to the metal bending.So domestic craftsmen often prefer to use ready-made pipes (any section), or even the usual metal barrel, if it is possible to find a suitable container size and wall thickness.

general scheme of the device homemade stove

metal stove for a bath usually consists of three main sections (bottom to top):

1. · fuel chamber (firebox);
2. · bunker with stones;
3. · water tank.

metal furnace is worth examining each element in more detail.

fuel chamber .There will be the combustion process, which requires door to load wood and a hole for air supply - ash pit .You must also remove the ashes, it was not necessary each time to shovel everything, including wood from the firebox.This is done through the ash pan - a special grille.

From fuel chamber heat from a homemade oven will rise in bunker with stones .For optimum heat transfer, the stones should be laid on the bars , which will connect the firebox and a stone bunker.These bins are closed and open.In our case, it will be closed.Well, to change the stones and splashing water on them, we will do a special door on the side of our stove (90 ° from the door to load the wood).

Then the heat will rise to tank with water .The maximum effective option distribution of heat - conducting it through the chimney .He will be responsible for allocating gas - combustion products.Pour the water in the tank can be over the top, but to make the sink of warm water handy at the bottom of the water tank is welded crane.

That's a short device self-made metal furnace for a bath.You can navigate to the manufacturing process.

instructions for the manufacture of the stove from a metal pipe

to create in the primitive conditions of the metal bathhouse stove with a diameter of 700 mm and a height (with tank) about 1600 mm, we will need:

• · sheet steel of a thickness exceeding 10 mm (dimensions of not less than 2,2 × 1 meter);
• · metal tube length of 1600 mm with a wall thickness from 7 to 10 mm;
• · Chimney pipe (diameter 100 mm from an arbitrary wall thickness - about 5 mm);
• · metal rod about 10 mm in thickness;
• · grate (sold in DIY stores, must be steel or cast iron);
• · 8 pieces hinges and latches 3;
• · faucet valve.

In the minimally need the following tools:

• · Saw-Bulgarian;
• · welding machine;
• · Metal scissors;
• · measuring tool.

Roadmap works

1. Cut the pipe into two sections:. 0.9 m and 0.7 m

2. At the bottom of the pipe (at a future furnace, indented from the "bottom" of about 7-10. You can see the ash pit and make the bottom, then it will be easier to remove the ashes - will need only to provide a suitable metal container under the ash hole) make a rectangular opening 20 × 5 cm - is the future of the ash pit.We must work carefully to subsequently use obtained by cutting a piece as the door.Higher ash cut out a hole for the fuel loading is also careful not to damage the metal.

3. welded to the outside of the pipe loop and ears for the latches, and do door - latch, set the door to the ash and the loading chamber.

4. Cut the sheet metal circle with a diameter of 0.7 meters, and in the middle - a hole the size of a purchased grate.If it was not possible to purchase, you can build it yourself from durable steel rod.The resulting welds metal circle just above the blower inside the pipe.The construction of the furnace can be considered complete.

5. Make the side (90 ° from the loading door and ash), cut-out for watering stones.We set the door to the above technology.

6. Now you need to build a platform on which are laid stones.Her we can produce from metal rods.The dimensions of the cell are taken in view of the size of the stones, which we plan to fill in the stove.

7. Now you can fill the stones.After that, cut out of sheet metal circle with a diameter of 0.7 meters.It makes a hole under the chimney, which should be located close to the far wall of our stove.Welded tube, then welded on the top of our hopper for stones obtained by a circle with a chimney.You can navigate to the manufacturing tank for water.

8. welded to our long pieces of a large piece of pipe length of 0.7 meters.

9. Making our water tank under the tap hole and fasten it by welding.

10. Cut sheet steel circle with a diameter of 0.7 meters, cut it into two unequal parts.The more we do for chimney hole.We fit over this part of the whole structure, passing through the chimney opening.Brew opening around the chimney.

11. It remains only to fix a smaller piece of a steel circle with hinges - through this hatch will be filled with water.All our homemade metal furnace stove is ready!

summarize

Having the skills of carving on metal and welding can be quite simple drawing on the stove to make the bath with his hands.However, it will require some time and material costs, but the savings will be substantial.And most importantly, this oven will work no worse than purchase.

Video - homemade metal stove with his hands