We are building a fountain in the country with their own hands

In the world there are many different types of fountains, and they all differ in both the technical solution and the power and size.However, most often in a confined space, such as in the garden area, the most acceptable option fountain jet type.That's such a small and not very complicated by the fountain, and will be discussed.

Even relatively small homemade fountain gives not only a beautiful view around the dacha, but also good for the overall climate of the area.The air around such a structure contains an increased concentration of ozone, and a fountain with running the entire section becomes cooler and more comfortable.

choice of location and equipment of the tank

Each fountain should be placed in a container, which serves to collect the water produced fountain.Naturally, the location for the construction selected, based on the total area of ​​planning.It should be sufficient for the construction of the pit beneath the tank and at the same time ensuring a good appearance of this part of the terrain.Before you begin to build a fountain in the country, it is necessary to consider the possibility of a free approach to the reservoir.This allows a good rest near the fountain, and to serve its component parts (if necessary).

depending on whether there is next big trees or not, and the method selected container constructions, and its type.The fact that the roots of the trees are growing.This may eventually cause damage to the bottom of the trench.If there is such a risk, it should be used as a reservoir special metal or plastic tub (Sales have different capacity, both in tonnage and in form).Often gardeners set bath b / u of the apartments.In this case, and not have to buy.A more expensive way to protect yourself from the roots - to make concrete bowl pit.And it should be just gidrobeton, as it will always be in the water.

Or lay out the bottom of the pit with stone and coat with a solution.But more still need waterproofing.If there are no trees, then there is an easier and cheaper way of equipment, and the bottom wall of the tank bowl - with the help of polyethylene film and geotextiles.A more expensive option of such a method - a special rubberized material surrounding the pit.

begin to address the following issues, namely, electricity.All pumps for fountains operate from AC power.Therefore, when choosing a place for a fountain, and you need to focus on the possibility of summing up the power cable.In addition to the pump, with the design of the fountain and take into account the need for electric lighting and automation of elements of the entire structure.

What do the fountain?

where everyone has their own vision of the general design of the fountain.Someone is building in the middle of the pit something like a rock, someone - a metal bowl, someone puts a sculptural composition.Sometimes an ordinary tube with spray water is considered sufficient for this.As you can see, the options are many.The only common rule for all - output pipe through which water and its diameter will be supplied.

First , the water from the fountain should not spill over the edge of the reservoir.In other words, the water supply and drain it must be consistent.Another caveat: if the water in the tank will not go away naturally, its stagnation will lead to decay of all "water body".The result will be not a fountain, a fetid puddle.

Second , the diameter of the pipe and pump capacity must also be related.It is necessary to consider, as a fountain stream should come under the pressure, and not just a weak stream, and sense from this fountain will be a little.We must not forget that the pump (pump) must be kept in the water, so the drain hole should be above the pump settings.

Selecting and installing the pump

Usually, such small fountains submersible pumps are used.Which pump you choose depends on the "quality" of water on the site.It should be guided to the pressure which is constantly present in the pipe, as well as variations of pressure.Such things often occur in areas that are connected to the general water supply system.Therefore, you should consult with a shop.Pump too much power to take it is not necessary, since the cost of the above, and at full capacity it will still work will be.

At the bottom of the tank is placed under the base of the pump.Depending on whether the cup is selected (described above was embodiments of tanks), and the base is made.The main thing - that the pump is smooth and does not fall in the process.If desired, it is masked, and the ways such a disguise on the Internet has a lot of material.

Choice of automation systems for fountain

and talk about it.Modern industry offers automatic fountains for different type and a different price category, the choice is large enough.Automation of even the most simple fountain should provide the engine off in case of overload, when the water in the water outage.If provided for different modes of operation of the pump, then switch their electronics should also.There are also various sensors (wind speed, for example).You can put a device and to the diagram, providing the switching modes of backlight.

necessary to take care of the external design, fountain decoration.It should have an attractive appearance from all sides.In the end, after all the trouble you will have a wonderful place where you can relax meditative, enjoying the peace.

Recommended video - a fountain made of stone: