Durable laying a solid board with their own hands

Popularity laying a solid board received due to the strength of the material.Externally - it has a lot to do with the floorboard, but consists entirely of solid wood.

Such flooring more durable and more practical, more resistant to aggressive external factors, can withstand greater loads and resurfacing.

begin installation solid wood is necessary at the very last stage of repair.In order not to have problems, it is recommended to study the characteristics of the material, find out more about the ways of laying, etc.

Application Method

produce reliable base - one of the important stages of the technology of laying solid wood.

Perform installation can be on a variety of coatings:

• cement-concrete or concrete screed;
• Plywood;
• Natural wood;
• on logs;
• on staples.

The most common way - laying a solid board on the concrete or cement screed.

Installation is carried out by means of adhesive, resistant to temperature changes and safe for humans.

If selected laying a solid board on the screed, it is tested for strength, absence of various injuries (roughness, cracking and chipping).

Photo:

humidity recommended surface - 6-7%.If it is higher, it is necessary to equip a waterproofing.

Not less popular laying solid wood on plywood.But it must be placed under an additional vapor barrier.

material humidity should not be more than 10%.Fixing is carried out using a two-component adhesive, pins for pneumatic gun every 30 cm make the hardware side.

traditionally considered laying a solid board on the joists, which are placed at the time of reconstruction work.

works are carried out as soon as possible and do not need to use cement mixture.Under lags plank waterproofing layer based on polyethylene film or penofol.

very interesting laying a solid board on the bracket.This method belongs to the category of floating, it allows you to save on carrying out installation work up to 30-40%.

aluminum products must be installed in conjunction with silicone bellows that enhance the connection ends.

often laying a solid board with his own hands made on an existing wooden flooring.But we need to make sure that the base of the old reliable, its moisture content does not exceed 8-10%.

The extra layers of coatings removed and the surface is thoroughly sanded to remove all the possible irregularities.

Video:

mounting a massive board direction must coincide with the direction of the old flooring.As mounting screws are used with corrosion-resistant coating.

learning more about what are the ways of laying solid wood, selected the most appropriate ones.

Preparations

necessary to prepare the next tool for laying solid wood:

1. Drawing accessories (metal ruler, pencil and Scriber);
2. spatula;
3. Joiner angle;
4. Pneumatic Tackers;
5. Screwdriver;
6. Drill;
7. Kiyanka wood;
8. Self.

recommended to buy screws for laying solid wood with corrosion-resistant galvanized.

They do not rust and smooth out the impact of seasonal fluctuations.Apply special parquet nails are not worth it.

bottom bracket can be mounted for laying solid stainless steel board.

They snap into a groove or screwed with screws from the back side and securely fix the two elements together.

mandatory training requires laying flooring of solid wood on the concrete surface.

direct contact between them is impossible, as it will reduce the service life of the flooring.

between planes create pad using primer and putty isolating film.The slots at the joints must be securely sealed.

Before answering the question of how to put solid wood, you need to prepare a building material.

It must acclimatization, after lying in a room up to 6-7 days.Products placed on the stand to allow for good air circulation.

For those who have already had to deal with floor coverings will not be difficult to perform the work on laying a solid board itself.Feeling a lack of confidence in their abilities, it is necessary to turn to the master.

Now a closer look at how to put solid wood and some rules to adhere to recommended.

Features laying plywood or wood flooring

has its own characteristics laying plywood for solid wood, which must be securely fastened to the main base.

recommend using material thickness 1.3-1.5 cm

Before mounting the plywood sheets into strips kroyatsya width 0.5-0.6 m

Video:..

Stack them is recommended at an angle of 40-45 degrees to the future flooring from an array.Recommended lanes between the gaps of 3 mm to compensate deformation during thermal expansion.

necessarily trail vapor barrier between the concrete and plywood covers.After polishing can begin assembling a massive board.

as a bridge using a two-component adhesive and pins for side mounting.

plywood may be laying solid wood floating manner.The peculiarity of the method is that the board and the base are isolated and fasteners made dies array.

This method is optimal for systems "warm floor", so that offset changes in temperature and humidity.

has much in common floor installation of solid wood on the old wooden surface.But this method is considered to be justified only in the case when the ground reliable.

Paul, calling into question, it is necessary to dismantle, as it will have a negative impact on the array.

on polished coating is recommended to lay the plywood thickness of 5-6 mm, but it may be any direction.

already mentioned, it is better to use two-component adhesive for laying a solid board on the basis of polyurethane.But it can be replaced by a single component MS-polymer composition.

Features of laying solid wood

explore options for laying a solid board and choosing the most appropriate of them, preparing the foundation, it is time to start the installation.

technology has much in common with the laying of laminate and all the work can be done by his own efforts.

Video:

necessary to clearly understand the rules of laying a solid board that no further problems.

If after several attempts the result seems unsatisfactory, consider and hire construction crew, which makes the whole range of works turnkey.

Typically, the scheme of laying solid wood involves screwing screws in increments of 25-30 cm.

From the thorn in the board you must drill a hole in order to avoid splits.

on a firm foundation laying solid wood floor is done with a special two-component adhesive.

alternative option considered elastinol or substrate on one side of the adhesive.

It has noise insulation and thermal insulation properties, thus it has gained popularity in high-rise buildings.

By fixing the boards, it is recommended to drive wedges for tighter connections.Between the flooring and the wall is left gap of up to 1 cm.

first row should be laid slot, turned to the wall.It is fixed on the front of it, which will close a plinth.

Laying solid wood flooring large board (width of 15 cm or more), the fixation is performed from the front side.

hats need to chime 8-10 mm in depth, and the hole closed with a special stopper of the same breed.

Many people may be interested in manual laying a solid board on the joists.It is recommended to use the size of a bar of 5x7 to 6x10 cm. In this case, its moisture content must be less than 10%.

joists are attached to the base using dowels or anchor bolts.The distance between fasteners is equal to 40-50 cm.

This styling lag made strictly perpendicular to the direction of the board and with an interval of 25-30 cm. The space between the joists insulation spreads.

Prices for services

If someone decided to turn to the professionals, you should find out what the price of laying solid wood.

It may vary and depend on the amount of work, the materials used and the number of required steps.

the market average cost of laying a solid board (relative to the walls of the square meters..):

• Perpendicular - 500 rub .;
• an angle - from 600 rubles.

Taking into account the cost of the training price mounting a massive board can reach 1500 rubles per square meter.m.