Bypass pipe stretch ceiling

Tension ceiling is one of the most popular ways of finishing in residential and public areas.This is due not only to its low cost, but also low labor and time consuming.In addition, the web will be able to mount even a layman, which also allows you to save.But even in the most simple work there are specific points that can spoil everything.In the case of stretch ceilings is bypassing communications.In this article you will learn how to work around a pipe stretch ceiling and to make the most of it carefully.

specifics of installation of suspended ceilings

Installation of suspended ceilings without the assistance of professional artists is a real, but still quite a challenge, so before you undertake it, thoroughly examine the entire theory and soberlyevaluate your abilities.This will help our article: "Stretch ceiling in the bathroom: the photo, the installation features", "Stretch ceiling in the kitchen photo editing features", "Matte or glossy stretch ceiling - which one to choose."

In each room there are communications that go up, so the need for bypass pipe stretch ceiling is inevitable.Here lies the risk of spoiling all covered by one careless movement - painting, especially plastic, is easy to break off in the direction when cut.It should take into account that most manufacturers offer a guarantee on its products only in those cases where the installation of a stretch ceiling is carried out by professionals from the same company.At first glance, such a requirement is not entirely correct, but in reality is quite justified and saves a lot of nerves on both sides.So if you decide to self-install, get ready to take full responsibility.

So when mounting tension ceiling there are the following typical situations:

1. necessary to bypass the heating pipe, located in the immediate vicinity of the wall.
2. Several tubes are nearby, vary in diameter, or suspended ceiling itself has a complex configuration.
3. bypass going around a circular element, the dismantling of which can be done only on one side (usually the extractor fan in the kitchen).

There are also non-standard situations that occur less frequently than usual.For example, if the room is a large column or other volumetric obstruction complicated configuration.In this case, more rational, and the easiest way is not to suffer from cutting out holes in the form of a column, but simply to establish two separate cloth and gently combine them with a special profile.

first method

most common and easiest way to bypass pipe stretch ceiling.Typically, it is used for white plastic blades and heating pipes, which are available in every room.

Step by step instructions for installation of the ceiling around the pipe:

1. Prepare your rectangular connecting profile made of plastic whose color matches the color of the canvas.The thickness of the plate should be 1-2 mm, and its dimensions have to close up the space of baguette at the wall surface of the tube point by about 1 cm. The width of the plastic profile should match the diameter of the heating pipe plus 2 cm margin.
2. Fill the canvas prints and perform the cut stationery knife or scissors with pointed tips.Plastic plates will hold the blade sliced ​​and did not give him "raspolztis" on.But even in this case should act very carefully, making minimally deep cut and tightly clutching a film to the pipe.
3. incision is best done in the place where the riser closest to the wall - so less likely will be seen in the case of defects errors.
4. At the end of the cut lines make the cut crosswise, so as to free ends of the leaf could link up neatly behind the tube without folds and tension.
5. Cut the unnecessary parts of the film, do not forget to leave 2-3 cm margin to fill their prints.
6. Install the pipe lining.This decorative ring can be made with their own hands Plastic suitable color thickness 2 mm, and can be purchased at the store.

This technology is used mostly for seamless installation of suspended ceilings with white plastic covers to crawl tubes.If you are going to mount the colored fabric, the pre-pick the appropriate shade laths.In some cases, you can play on the contrast, for example, picked up a purple patch to yellow canvas.

Tip: If communication between the wall and very little space, it is not necessary to look for a suitable length of plastic - you can simply cut the reinforcing ring of the corresponding diameter.

second way

There is another way to stroke the pipe stretch ceilings, used for surfaces of complex configuration, or when the room is installed pipes of different diameters and standard pads are not suitable for them.In this case, the plastic ring to be installed is not outside, but inside the web.

Instructions circumscription of plastic pipe stretch ceiling:

1. Heat ceiling fabric to the desired temperature, and tighten it up a baguette.
2. Hold the tape, make sure the markup in the center of the pipe.If you miss a little - do not worry, because in the case that the web can be lightly tighten, thus compensating for the slight defects.
3. Glue to the back side of the fabric-reinforced polyurethane ring to it was located closer to the wall.
4. When the glue is how to seize, take a cross-sectional view on the canvas in the center of the ring.
5. Pass the edge of the section up through the ring, and then CONNECT them, that they held on to the top of the reinforcing ring.
6. Cut the fabric in the direction of the reinforcing ring to the nearest wall.
7. Wear ring tucked in his canvas on the pipe.
8. edges cut CONNECT to one piece of a plastic pad that will function as a kind of lock on the cut.
9. Glue harpoon a small segment of the web.
10. Tension ceiling from the nearest corner.

These plastic rings can be installed not only to circumvent the heating pipes and other communications, but also the installation of various fixtures, alarm sensors and other equipment.To learn how to install the reinforcing ring and crawl tubes in stretch ceilings - in video instructions below:

What about the hood?

would seem to manage to extract is no more difficult than with the heating pipe, or any other obstacle, but in this case, the problem lies in the features of the device operation.The fact that during the operation duct exhaust is strongly heated, which may well lead to melting of plastic stretch ceiling.

In such situations, you need to ensure maximum protection of PVC film, erecting Temperature resistant barrier.The easiest way to do this with plasterboard segment.Plasterboard is an environmentally friendly material that is often used specifically to enhance fire safety when decorating work.The second option - instead of the usual corrugated exhaust pipe installed sandwich pipe with double wall and thermal insulation layer between them.There is such a duct is more expensive but lasts longer, and looks much like a lot more than ripple.

To protect the edges of the ceiling of the film, use a ring made of heat-resistant plastic.Exactly the same ring is applied when mounting fixtures, as well as hot pipes traversing heating.

History

Stretch ceilings seem modern and unusual way of decoration, but few people know that the first stretch ceilings were popular in ancient Egypt and Greece.Of course, if not used PVC film, but the technology was virtually identical - to the ceiling stretched silk cloth decorated with patterns.When after a while the fabric began to sag, or the owner of "apartments" would like to change the interior, workers simply pulled new canvas top.

In medieval Armenia also practiced technology of suspended ceilings, but that is not used for silk and cotton cloth soaked in a solution of chalk.She pulled on a special frame around the room (do not remind you of anything?), And when chalky solution dries, the fabric is stretched independently and on it there was not a single crease.Some artists today are practicing this method, but instead of chalk used water-based paints.

In the early 70-ies of the last century began to use cloth instead of light polyvinyl chloride film, which does not sag and served much longer than any fabric.It happened in France, so the ceilings originally called "French."As the saying goes, everything is new - it's like to be almost forgotten the old, and in the late 90s appeared on the market and the fabric ceilings.They quickly gained popularity, since it does not require heating, reducing the risk of damage to the walls and the complexity of the work as a whole.Today, the market presents a wide range of film and fabric ceilings for everyone, and we hope that this article will help you make the installation quickly and beautifully.