Build Daily

Equipment

August 12, 2017 18:06

Washing machine flows from the bottom : the reasons for what to do if a leak during the spin cycle

click fraud protection
Washing machine flows from the bottom
  • Through it flows?
    • hose
    • drain pump
    • tank
    • cuff
    • Near bearing
  • Other reasons
    • clogged feeder washing powder
    • damaged pipes

Washer is designed to make our lives easier and more convenient, allowing us to spend on housekeeping less time and effort.Sometimes, however, as a result of careless handling or factory defect, it is true of the assistant becomes a real source of the problems.One of the most common problems - the appearance of a leak in the bottom of the case.If the washing machine runs at the bottom set of water when washing or spinning, you should look for the cause immediately.

In this article, we will tell you how you can identify the source of the leak, and how to fix it.Our tips apply to washing machines from the most popular manufacturers, such as LG, Samsung, Bosch, Electrolux and Ardo.

Through it flows?

The first thing you need to pay attention - at any stage of the washing cycle under the washing machine begins to form a puddle?This will help you to determine the cause of the leak.Upon completion of the unit, disconnect it from the mains and carefully inspect the main structural elements.Pay attention to the integrity of the components and for the presence of residual moisture.

Flowing washing machine

hose

If the machine starts to leak when dialing or draining water, the problem is most likely in one of the hoses - water inlet or drain. case of breakage of the first leak occurs during the spin cycle, and if faulty the second - in the process of filling the tank.

detect a leak in a hose is quite easy - you just need to conduct a thorough examination of these elements and check the attachment points to the connection to the sewer and the body of the washing machine.If the integrity of the hose is broken, you need to buy a new one.

recommended to replace the gaskets and tighten the attachment manually When loose (since the tools can damage the plastic).

Flow through the hose washing machine

drain pump

Broken drain pump - it is a serious nuisance.To cope with it on their own, without having any knowledge in the repair of household appliances, it will not be easy.Therefore, the most correct solution - call the professional wizard to the repaired pump.You can also buy a new item and try to install it by hand.

The drain pump of the washing machine

tank

If leakage occurs directly in the washing process, most likely the problem lies in the tank.Often we forget to wash extract from the pockets of small things.Forgotten keys, pins and coins can damage the fuel tank of the washing machine, especially if it is made of plastic.Slot detect simple: only need to remove the front and rear panel of the washing machine, and tilting it in different directions to inspect the tank.Is highlighted a flashlight that you are not escaped even the smallest crack.

small tank damage can be repaired using a special construction glue, but it is a temporary measure.In large pot holes need to be replaced.

Tank washing machine

cuff

cause of leakage when washing machine may be a violation of the integrity of the cuff - rubber pads on the hatch.The cuff may tear due to contact with foreign objects or simply wear as a result of long-term operation.Damaged cuff should be repaired or replaced.And then, and more can be done with their own hands.

holes can be repaired using special tools such as "liquid rubber", or pasted on her rubber patch.For information on how to dismantle the old and install the new cuff described in the article "An unpleasant odor from the washing machine."

Cuff washing machine

Near bearing

If the washing process is accompanied by not only the formation of puddles of water under the washing machine, but is noisy, the problem may be a faulty bearing.During operation of the bearing is covered with rust and patina, which is why suffering is not only he, but also located near the gland.That is why these two parts made at the same time to replace.To reach them, the unit will have almost completely dismantled.

Repair of washing machines bearing

If you are not confident in their abilities, it is better to entrust this task the professional as their inept actions you can further aggravate the situation.Determined to correct the problem yourself, do not forget to take pictures of each step, a marker to mark the location of the wires, and other important details.

process of replacing the bearings presented Vladimir Khatuntseva in the following video.

Other reasons

Clogged detergent powder feeder

arisen at the beginning of the wash leakage may signal that not all is well with the container, the feed powder and conditioner.Sometimes he hammered excess detergent or accidentally fell into objects.The solution is to, well cleared feeder and after washing it in warm water.In the presence of cracks it should be replaced.

Cleaning the detergent powder feeder

damaged pipes

If the washing machine is leaking at a set of water, a possible reason for this - damaged pipes.It is about pipe connecting the filling valve and washing powder feeder and a pipe that connects the tank and drain pump.Another pipe, which may be responsible for leakage - one that delivers water to the tank.If the problem is not very serious, all can be corrected with the help of sealing means, otherwise the damaged pipe to be replaced.

About repairing the washing machine with a leak downstairs watching a video of Vladimir Khatuntseva.

instagram viewer