How to make an apron in the kitchen

wall area in a working kitchen area most susceptible to contamination.Splashes of water from a sink or a red-hot drops of oil from the pan eats into the walls and hard to clean.To facilitate cleaning and decorative purposes settling kitchen apron.

original and practical apron in the work area may be oneof the main kitchen decoration.The style and design for the kitchen apron is selected based on the overall interior design.Materials used varied.The most common is the tile, but also protective panels made of MDF, plastic, glass and other practical materials used.Choose apron design for the kitchen is not difficult, guided by a photo from the Internet.

Forms and materials for kitchen aprons

a traditional apron for the kitchen ceramic tile.The advantages of such an apron applies resistance to water, detergents and temperature extremes.

1. Ceramic tile is easily washed and is very durable.Choose tile can be of any color and size.Looks nice apron of tile trimmed contrasting or matched in tone edging.Often used to insert special decorative tiles and panels.
2. Protective apron made of glass - a relatively new but promising trend in kitchen design.Beautiful and elegant pattern applied to the surface of sand blasting machine glass panels using laser technology.Perform such aprons continuous web, and there are no seams on the panels.Glass is neutral to any chemical irritants, and the absence of joints makes it easy to sanitize.Glass panels are quite expensive, and the selection and installation is reasonable to attract specialist.
3. Inexpensive will cost an apron for the kitchen made of plastic.Decorative plastic panels mimic ceramic, wild stone, ceramic tile, etc.Installation of the panels is quick and not too difficult.Plastic panels have a lot of positive qualities.They weigh little and are easily replaced if damaged.The only disadvantage of plastic panels - Do not use abrasive cleaning agents.Perhaps the appearance of scratches or scuffs the surface layer.

can opt for a kitchen apron made of MDF panels, mirror paintings or recruited from the mosaic tesserae.

apron kitchen laying of ceramic tiles

Equipping apron for the kitchen, the dimensions are determined on the basis of expediency.For glass or mirror panels, the dimensions given in the production.

1. mount your own apron made of ceramic tiles, the length is determined by the location of cleaning and cooking stove.At the height of the apron made by shear protective cover plate.About 55 cm from the work surface, or 1.5 meters above the floor.
2. wall surface is prepared for the installation of ceramic tiles.In the markup section of the wall is removed the old wallpaper, paint or other finishing materials and old plaster to the base.The plot is leveled, as in panel houses with concrete walls can be an old ax or chisel to put a notch herringbone.
3. tile is glued on the bottom corner.On the back side of the trowel to apply adhesive for tiles, cement-based and leveled with a spatula.To create smooth joints installed plastic cross.
4. Sticking 8 - 10 tiles, laying open their check with a spirit level, erase the seams and allow the glue to grab.Move and align the tiles can be 18 - 20 minutes.Then continue to spread with a few interruptions for setting glue and verify the installation.
5. Crossings remove as setting and drying of the adhesive solution.Stain solution tile adhesive clean during installation.The next day, engaged in grouting.Picked grout for joints, in harmony in color, contrast or color companion.Contrasting colors are used in the case of grout perfectly smooth seams.Blending in with the color of tile grout used to hide imperfections and other faults during installation.

For grouting a steel or rubber trowel.For wide joints sometimes applied jointing.

Installation panel for kitchen aprons

1. Aprons kitchen of plastic panels, MDF, boards, or other similar materials are installed on the same circuit.The height and contour of the apron for the kitchen of the panels is planned taking into account the hinged cabinets and kitchen furniture.
2. On the kitchen wall mounted crate - frame for fixing the panels.It lathing made of timber or profile rail.When selecting a timber is taken into account the thickness of the timber and panels.To save space crate deep into pre-punched grooves.
3. mounted on the frame profile mounting rails, which are installed in the panel.The connection is performed on the mounting screws, or special locks.
4. Frameless installation of plastic panels produced by a suitable adhesive or liquid nails.Choosing a kitchen apron for materials, check the hygiene and quality certificate.

Before starting work, you can see the installation of the apron for the kitchen, there is a video at the end.Installation of glass or mirror panels for kitchen apron best left to professionals.When installing such panels is required to take into account many specific nuances and one pair of hands is not enough.