How to take a bath : step by step instructions

As a rule, dismantling bath produced in the course of repair work across the room, or the replacement of sanitary equipment.In any case, you'll need a step by step guide of how to take a bath, so as not to damage the lining elements, furniture and other plumbing in the bathroom, to make the job quickly and efficiently.

preparatory phase and the beginning of work

Althoughthat in the process of dismantling you still produced garbage, pre-cleaning and preparation of the premises is a necessary step before starting work.If this complex repair, the room should not remain anything, until the shells and hoses.Experts recommend to dismantle the bath in overalls and protective equipment.You must be prepared for the fact that the work to be pretty easily soiled and dirty.

So, before you remove the old tub, you must do the following:

1. completely disable all communications in the bathroom: shut off all the water inlet valves.
2. endure all the accessories and bathroom accessories.Even if they will not bother you, you still run the risk of severely damaging soil or hopeless.
3. Move out of the room all the furniture: tables, cabinets and so on.
4. dismantle plumbing and sanitary ware.
5. Clear the room of anything that may interfere.

Quite often, dismantling the bathroom is directly connected with the overhaul, which involves the removal of tiles, glazed tiles, stripping of paint and other coating materials.Everything is done mainly fast enough, but at least the day you leave.

also advise in advance to ask, Is there in your home service export of bulk waste.Otherwise it is necessary to engage in the export of old bath itself, which is quite difficult.

Getting dismantling

When all preparations are done, you can proceed directly to the dismantling:

• first step is to disconnect the drain pipe.If your plumbing is from the time of the Soviet Union, then, most likely, the pipe is cast iron, coupled concrete solution.Naturally, such a construction is secured tightly.The easiest way is simply to cut the pipe such that nothing not to lose time.In any case, you are unlikely to use them will become in the future.But plastic pipes simply roll out and put on the dismantling in the other room.

• Before you clean the bath, remove the floor siphon and overflow pipe.Siphon in most cases fixed clamping bolt turned towards the drain grating.Suffice it to rotate it in the opposite direction and unscrew.Thereafter siphon detached without any problems.It happens that the clamping nut is difficult to unscrew.If she does not give in, and need for its subsequent use, you can simply cut it hacksaw.They are made such nuts mainly of soft brass, so much effort for cutting is not required.If a hacksaw work is inconvenient, you can use a chisel and hammer.Just knock it carefully, trying not to damage the bathtub.

• Now you need to make lateral cuts.They are made flush with the inner side of the lattice so that the distance is sufficient for cutting sector of the discharge funnel.of its size at the same time should be no more than a quarter of a circle.
• Then gently Saw circumference of the funnel.Most importantly - do not damage the enamel.But this is only important if you are to mount a bath again.If not, you can work faster and without special care.The fact that in the end will be from the sink, push the edges inward, bending a chisel and hammer.Now drain easily pass through the drain hole in the bathroom, and you can easily get it.

• Unplug the drain and overflow pipe and pull out of the sewer socket outlet tube.To avoid dripping, he can close the funnel gag or just wrap a piece of used cloth.If the bath has been grounded, the strip must be removed so that it does not interfere with work.To do this, simply knock hammer metal wedge.Some of the tiles in the bath edge and often have to clean.
• is now possible to release the bath from the adjacent cement.Again, if the bath you will no longer plan to use, special care is required.You can just beat the cement chunks.It is likely that it will fall away with the enamel.However, if all the plumbing to be installed back, we must act cautiously.The upper layers of cement can be removed by the same chisel, but do it very carefully.Next will have to work more subtly.You can use a knife, spatula or any other metal sharpened, everything is handled very carefully.On top you can walk sandpaper, but it also can cause damage to the enamel, which in the future will cause corrosion.In any case, if the bath was fixed concrete solution, then do all the work perfectly is unlikely to succeed.

Features of dismantling of different types of baths

The whole process in all cases is quite similar, but different weights involves specific features and causes some difficulties.Therefore, select the key points of the process in each individual case.

Dismantling the iron bath.The problem is that the reuse iron bath is usually not possible.Therefore, the main tool for dismantling will be the hammer, which will be split bath.The metronome

pieces of cast iron tubs - the process time-consuming and very noisy.From general considerations recommend to warn the neighbors, that at a certain time you will carry out repairs to avoid later complaints.

Iron - the material is very hard, but it is quite fragile, if you work with the force.Slugger as the smaller pieces of metal can be, to be able to immerse them in a bag and take out of the house.The advantage of breaking down the cast-iron bath - avoid the need to hire a special equipment for export.The pieces can be loaded even in cars, take to the dump or to pass on the scrap.

If you do not want to work many hours with a heavy hammer, you can use the grinder with a special disc-nozzle.The pieces will be smoother and more convenient for fans.

Important!In this paper, use personal protective equipment: gloves, sunglasses, closed shoes.

about how to remove the acrylic bath special detailed instructions are not required.It is quite easy and hassle-free place in the doorway.It can also be sawed and removed without any problems.

should be said that acrylic bathtubs many agree to take a Pickup, which will save you from further trouble.

steel bath Dismantling the principle is almost identical to the dismantling of the iron.For cutting strong enough to pick up the circle and grinders.But if the bath is very small, weighs little and is easy to pass through the door, then saw it is not necessary.You can even just make it to the street.You can be sure that it will be taken immediately.

Tips and tricks

Despite the overall ease of use, there are a number of nuances that must be considered in the work.Therefore, we offer you a set of basic tips that dramatically simplify and accelerate the process:

• If the bath is easy and takes place in the doorway, not to saw it.Save your own time and effort.When
• take out of the room bathroom, which will be installed back after repair, mounting angles are better to paste over the film, so as not to damage the enamel, if you hit it on the opening corners, etc.
• careful not to damage parts of the mounts.Try not to lose them.Without these elements set the bath again it will be very difficult and it will be unstable.We'll have to go to the nearest hardware store and buy new ones.
• advise immediately during repair and replace all the branch pipes.Even if they are changed relatively recently.You can easily damage them, and after the installation of a new plumbing replacement process will be very complicated.Replacement is not much impact on the cost of repairs, but will prevent the additional costs of time and effort in the future.
• pipe joints is recommended to handle quality sealant.It is rather a preventive measure, but it will never be superfluous, and provide a long service life.
• Before you make a bath, if possible better to remove the legs.You most likely will put it in another room, and metal supports can greatly damage the finish.It is safer to remove them and just fill up the tub side in a new location or to back against the wall.
• When the bath lift vertically, it can go ahead on the tile.To prevent this, you can lay under it a normal rubber mat.This will provide excellent adhesion to the surface and a greater safety in operation.
• If one side is firmly attached to the wall, you can simply lift the opposite side and "drop" it on the floor.But care should be taken to mitigate the shock: lay the fabric, rugs, etc.But if you live in an old house with a weak overlap, this method is strongly discouraged.

As you can see, the process of dismantling itself is not a big deal, but at the same time requires considerable effort and time.Therefore soberly count your own time and effort.It was only after the final repair work to proceed.More familiar with how to remove the bath can study video.