Assembling metal furnace for a bath with his hands

If the country planned to build a bath, it's worth thinking about how to build a metal stove for a bath with his hands.

Of course, the quality of the bath depends on its design, but plays an important role and the furnace, which will provide the desired temperature in the interior space.

Homemade metal furnace in this case are the best solution, which also can fully realize their own hands.

Its manufacture with their own hands with the right approach does not take a lot of time, and in addition, will reduce financial costs.

According to its characteristics and the reliability of such a furnace in no way inferior to brick, and provide a space baths good heat if necessary.

In addition, for ease of homemade metal furnaces is further equipped with a special tank, which will always be hot water.

For more information on how to make your own hands from metal furnace, described in the video, which is available below.

Video:

Features furnace of metal

Metal furnace, which can be done byarms, has a number of advantages compared with the more familiar, made of bricks.Such

furnace operates on the principle of continuous burning, which means that the fire in the furnace should be maintained in continuous operation.

addition it should be noted that the use of the furnace, made of metal, the inner space allows warm bath for one hour.

This figure is for the brick oven is about three hours.Also, the metal furnace cooling occurs just thirty minutes.

Installing such a furnace in the bath should be carried out in strict compliance with fire safety measures.This is mainly due to the fact that its metal wall is strong enough warmed up, which in some cases may cause a fire.

It is advisable to install the oven made of metal in the baths, which have a relatively small space for the full and effective warm-up areas with large internal volumes will have to significantly increase the rate used for its warm fuel.

Structurally the oven, made with metal sheets, can be performed in a variety of ways.It can be done with an open stove and closed.

addition, there are no restrictions on its configuration and as well as location.

for its production allowed to use scrap metal materials, but only with sufficient thickness.

as the base material for its construction suitable steel sheet and old tubes barrels.Also allows free arrangement of its individual elements.

In what furnace construction stops specifically, should be determined on the basis of several different factors.

First of all, to consider directly the size of the bath, and in addition, based on the presence of certain materials and skills.

There are special drawings, which are painted in detail the design features of absolutely all of its elements.

For more information on how to make your own hands from improvised oven metallic material, described in the video below.

Video:

Getting Started

Before you make the furnace for a bath of metal, should be using the drawings, to prepare all the necessary materials and tools.

most simple structure must consist of several separate elements, including a water tank and the furnace.

necessarily need a steel sheet, the thickness of which must not be less than eight millimeters for their manufacture.

Also, be sure to need the appropriate pipe diameter and thickness, as well as the metal rod and the grate.

also need to have a strong latch, by means of which will be closed all technological doors.For the removal of the products of combustion flue pipe is required.

should also have on hand a crane, which will subsequently be mounted on the tank with water.

of the tools for the manufacture of this type of furnace need to be grinders, through which the metal of appropriate dimensions will be cut.

Since all connections furnace elements must necessarily be made of steel, it is necessary to purchase a welding machine.

also in the preparatory phase should take into account the structural features of some selected elements.

camera, which will be burning fuel, necessarily must have a door and a small technological hole for supplying the necessary air.

In addition, you must provide a small and technological hole to remove accumulated ash.

should also think about the structure of the space for the stones and place the tank arrangement with hot water.

Having on hand the drawings and all the necessary material to work, you can begin to assemble the furnace for a bath of metal sheets by hand.

phased assembly

After all the necessary tools and materials will be prepared, you can begin to work with their hands.First we need to make the furnace and heater, respectively.

For these purposes, you should use a large piece of pipe.It is a technological hole, which will be used as ash and above him developing are mounting under the grate.

next step is to firmly secure the door and on the opposite side of her to do another hole through which water can be cooled stones.

Next settling hole under the chimney and the installation is made directly by the chimney.

should be noted that all fasteners and welds of the furnace for a bath should be as airtight as otherwise the combustion gases will flow into the interior of the steam room, which means that the room will not be used for its intended purpose.

is followed properly equip a special water tank.It was collected during operation of the remaining piece of the metal tube.

This piece must be installed and securely fastened by welding on top of the stove.At the bottom of the pipe should be installed under the hot water tap.

After that you should take care of the cover, which will close the tank.It can be manufactured from a circular shape corresponding predetermined diameter billet.

This blank is cut down the middle into two equal parts.Water from parts make technological hole for the chimney and tightly fastened by welding directly to the tank itself.

second half pipes are fitted with hinges and handle and is fixed on the tank.Heats the water in the tank will be at the expense of smoke that will rise up from the stove.

For more information on how to assemble without assistance of metal furnace for a bath, talked to the video, which is available below.

Video:

installation rules

Installing a homemade furnace to be made, too, with his own hands made of metal, should be designed at the stage of construction of log bath.

place where it will be, must necessarily have melkozagublenny foundation of reinforced concrete.

also its installation requires that fully complied with fire safety measures and rules, as the room is considered to be the object of increased danger.

immediately before the installation should be on a pre-construction of the foundation laid in two rows of special firebrick.This is followed by the installation of all the rules of the furnace itself.

unit must be at a distance from the wall surface at least one meter.

If the structure is completely made of wood material, the surface of the walls should be mandatory to protect the special fire-resistant foil, under which must also be a heater.

This will help prevent overheating and possible fire, respectively wooden wall surface.

Installation of metal furnace in the bath also includes installation of a chimney, which should be possible to isolate from the interior space.

As a material for chimney probably best to use the sandwich pipe.

In this type of pipe between the inner and outer space enclosures specially laid a layer of a special heat-insulating material.

In the case where a metal chimney stove is made not of bricks and a metal sealed tube in the location where it will be displayed from the interior to the street, it should arrange a special pass technology channel.

Video:

This hole is further isolated and sealed after the pipe is securely fastened.Experts recommend the oven ready to impose further firebrick.

This will not only give the oven a more attractive appearance of the metal, but also give the opportunity to protect themselves from accidental burns.

In this case, the heating unit can be placed at a distance from the wall surface equal to twenty centimeters.

In any case, for a small bath is the best option is oven, made of metal.

It does not require significant cash expenditures, going quite quickly and without assistance.In addition, there will be no difficulties and its subsequent operation.