How to repair washing machines with their own hands

Many choose repair washing machines with their own hands, becauseFirstly, it will help significantly to save on professional involvement, and, secondly, are often damaged cars are not as difficult to them could not understand a person without much experience.

There are few of the most common problems that prevent owners use their washing machine with a vertical or horizontal loading.

Sometimes the device may not be included in the machine can not do water, or comes back too slowly.

Some devices cease to heat the water, or suddenly stops during operation.

Other common problems include stopping the rotation of the drum of the machine, the lack of drain water or too much water flow out of the car, the noise or vibration during operation, as well as the inability to open the door at the end of work.

article we will examine the most popular reasons for breakdowns washing machines, as well as show you how to carry out their independent repair.

Videos with step by step work will help you cope with the task and bring his semiautomatic machine or device with vertical load to a working state.

problems in the washing machine

If you can not turn on the car semi-automatic, or with vertical load, it does not dial or does not heat the water, or in any other way fails to fulfill its basic functions, you must first look into the manual - perhapsthese problems are caused by improper handling of the device.

If the machine does not start, first make sure that you choose the right wash cycle and shut the door firmly and connect the machine to the network.

Video:

When connecting, you will notice that the plug device is faulty, and that's why the machine does not work.

also need to make sure that cranes, through which the car semi-automatic, or a different model enters the water, were discovered becauseIt is also part of the reason why the washing machine can not be included.

If you find that the problem in the wiring, it is necessary to remove the plug from the network, remove the outer panel from the machine and clean it, if you see the processes of oxidation.

also need to ring the power cord and the possibility of failure, becauseoften the machine will not run because of this problem.

machine can not run due to a timer malfunction.

To learn how it works, you need to switch programs until the drum starts.If the problem is in the timer, you need to buy a new one.

Other possible malfunctions that prevent the launch of semiautomatic machines, and how to address them, look at the video.

Video:

If the device does not enter the water, the first thing you need to check whether the valves are open to its filing, as well as to assess whether the inlet hose in order.

If he flattened or deformed, then it must be flushed through and return to their previous position.

Perhaps in the car clogged filter to make it self-repair, close the valve and separate the hose, then remove the filter pliers and rinse it under water, and then insert into place and connect all communications.Watch the video, how to do it.

Perhaps damaged inlet valve.In this case, you will have to purchase another valve.

It is the same place where the inlet tube, more information on the device of your car will give you instruction manual.

If the drum machine has stopped rotating, then maybe you forgot to remove the device breaks or loose wire belt.

But do not pull it too hard becauseIn this case, bearing wear, boards, or motor belt may occur prematurely.

To prevent damage to the quality of bearings, circuit boards and other components, check belt tension: If you press the offset is 12 mm, it is correctly tensioned.

If the machine is semi-automatic, and there is no belt tension, you will need to buy another.

drum machine can not operate if the door lock damaged cars.Perhaps latch stuck or is broken.To find out, click several times on the arm of the machine.

It does not work, it means that the latch is damaged.Finally, the problem may be a faulty engine.

It will likely not be able to fix even with the help of a video, and it is better in this case to turn to professionals.

Video:

If semiautomatic machine with vertical load or stops during operation, the first thing you need to check whether you did not put it on pause.

It may also be that the reason for the power transmission interruptions, because of what the machine was disconnected.Often the problem lies in a faulty pump, which may clog or break.

To do this, remove it and check for problems and replace if necessary.How to remove the pump from the washing machine, look at the video.

Other possible problems

Over time, the semi-automatic machine, and others begin to make noise during operation.Often the problem is a fault in the bearings, and boards, but may be other embodiments.

For example, if you left the keys in the pockets of clothing or coins, they will knock during rotation of the drum.

If you notice a problem, you should immediately remove the extra items, or semi-automatic machine or dryers can come to a fault.

Video:

noise machine can and if the latch on the door was broken.Then the sound will be buzzing, and will end when the door is closed tightly.

If wired machine belt slips, it will also affect the volume of its work.With such a failure will sound shrill.

damaged belt should be tighten, but not too much, to avoid damage to the bearings and boards.

Some semi-automatic typewriters can not do this, then the item you want to delete.
most common cause of noise - bearing failure and boards.

Faulty bearings and fees can be found on typical cod machine.In this case, they will have to change.

To perform high-quality repair of bearings and boards, watch the video instructions, or invite a specialist, if you have little experience in the repair work.

If the washing machine vibrates or "jumps" during operation, the cause may also be a problem with the bearings and boards.

However, this may be due to the banal overload the machine, if you overdo it with the load into things.

Video:

machine can make noise due to the fact that things went awry inside and turned into someone.To get rid of vibration, it will be enough to unravel them.

If the surface on which a washing machine, irregular, the device will jump.

Ideally machine legs should be at the same height, but if you can not do it because of the uneven floor, at least the missing sheet under the floor-foot piece of fabric or linoleum, to minimize the height difference.

machine can "jump" if it was broken or weakened by the suspension spring mounting ballast.In both cases you will need a repair, if burst loads, they should be replaced by others.

If you just loosened the bolts on which the ballast is attached to the tank, then they need to be to tighten.

A common problem faced by owners of vehicles: after work, water from it is not emptied.

First look at the mode: The unit must not stand on pause or be delayed washing mode.Sometimes water can not merge due to the fact that the hose is damaged.

It should be flushed, and remove it from foreign objects, if they are present.

Often water is not discharged due to the fact that the exhaust filter is damaged.Often applied in machines being protected by this device from debris.

Sometimes enough to wash out the filter, if it is clogged badly, you have to change it.How to do it, look at the video.

fault may be in the pump machine: it can break or become clogged.In any case, in order to check this, you need to remove the item and see whether it unnecessary items.

Before you do this, lay a cloth on the floor, so as not to fill it with water.

Video:

necessary to turn the filter check hose clamps for clogging, and see if the impeller rotates.Use the pen or pencil.

possible that the car has worn switch, which is responsible for the water level.Fix it can not only be exchanged for another.

Sometimes water is not discharged due to the fact that the work of the machine is suspended, for example, due to a failure in the power supply.

To ensure quality installation, remove the device plug and see if contacts are moved.If there is oxidation, it is necessary to clean them.

If the machine broke down timer, then it will not be able to function properly, including the drained water.In this case, the item must be replaced.

If during operation of the machine is leaking a little water, then it could be that eased the hose clamp.In this case, water is around it.

can tighten the connection details to get rid of this problem.If the water flows from the crack in the hose, it will change it to another sincefix will not work.

Video:

Finally, the water may appear due to the fact that the door seal apparatus hitched.In this case, the repair is also impossible, and the item must be replaced.

As you can see, to repair the washing machine is often difficult, especially when handy guide and video to scheme how to troubleshoot.