Glass balcony aluminum profile

practice of recent years shows that the balcony glazing aluminum profiles used in all climatic zones.

Looking at a photo of multi-storey houses, the owners of apartments, where glazing is still missing, decide on the immediate installation of protective structures.

In order to perform the installation with their own hands, it takes some training.

In the case of thermal insulation of balconies and loggias there are enough nuances and subtleties to be aware of.

preparation for installation, you need to start from the balcony of the survey.Then it does the calculation of material requirements and the cost of all work.

Then you can proceed to the practical implementation of the project.

preparatory stage

Currently glazing of balconies and loggias is performedthe construction of houses.This decision was due to the growing demands of owners of apartments to quality.

simple wooden frame protects the balcony from the snow, rain and dust.If the balcony to warm, then it turns into a full room, suitable for a comfortable stay.

In view of these facts, the glazing is of the following type:

• cold;
• warm.

Intending to spend equipping the balcony with your own hands, you need to decide what type of design will be installed.

this purpose should be to estimate the strength of their balcony, its orientation to the sun or the shadow side and the condition of the house as a whole.

Video:

The panel houses of mass building balconies have a minimum area.Availability loggias typical project does not foreseen.

In order to equip the balcony, you should choose one of the existing glazing methods:

• normal;
• combined;
• frameless.

The usual way is to ensure that on the balcony installed wooden frames.The glass in them sometimes tinted or decorated with glued stained glass.

Such glazing protects from the street noise and raises the temperature in the protected volume of a couple of degrees.

This design can be built with their own hands, but the protective effect of it would be minimal.

combined method of glazing of balconies and loggias includes a conventional cold glazing, in addition to which the room is insulated.

This option does not require large expenditures and allows you to get a good result.Frameless way to loggias and balconies arrangement is used in large rooms.

Before starting work, you must carry out a detailed account of all future costs.Most often used aluminum profiles when choosing frameless method.

cost of the metallic elements is small, but the installation of the guide profiles and tuning swing-out mechanism requires highly skilled and highly valued.

design Choosing

Cold glazing of balconies and loggias is preferably made of aluminum profiles.Today the market offers a wide range of aluminum profiles.

first advantage that aluminum has over other materials - its light weight.The photo shows the balcony, protected by a frame made of aluminum profile.

operation aluminum construction period exceeds 50 years.This important fact must be taken into account in the preparation of cost estimates for the installation of the glazing.

rolled aluminum cost is significantly lower than the PVC profiles.To this we should add that aluminum is the best way complies with fire safety requirements.

Among the disadvantages of aluminum profile called its high thermal conductivity.At arrangement of loggias and balconies, this factor is of weighty importance.

formed the view that aluminum structures are used when performed in a cold environment glazing professionals.

To compensate for this weakness, manufacturers began to produce profiles with an air cavity inside.To enhance the heat-saving effect of this cavity is filled with a special material.

In addition to this, instead of glass windows are installed.An elementary calculation shows that this improvement brings aluminum construction on the first positions in the ranking.

appearance on the market of finishing materials of aluminum profiles, allows you to perform with the removal of the balcony glazing.

The photo shows the appearance of the balcony after the work is completed.

In this embodiment, the balcony width increases of up to 30 cm.

mounting technology allows the aluminum structure with the removal and not to increase the burden on the balcony railing, as their weight is minimal.

The small volume more convenient to use a sliding window opening system.From aluminum extrusions such a system can be skomplektovat and install their own hands.

Installation sequence

glazing of balconies and loggias begins with a complete set of materials and fasteners.

If you decide to perform all the basic work of their own hands, it is required to make a preliminary calculation of the glazing area.Depending on this parameter selected frame type.

In their function frame of aluminum profiles are divided into the following types:

• deaf;
• swing;
• sliding.

swing window is set to a wide balcony.If the width of balconies loggias or small, it is recommended to opt for the sliding mechanism.

In order to provide quality ventilation of the room, you need to install two opening four frames deaf.

Preparation balcony

This video shows how to perform preparatory work for the glazing of loggias and balconies.If on the balcony wooden frames have been installed, they must be removed.

This terrace area is freed from all things and objects.It is necessary to check the strength of the parapet.

Video:

In older homes concrete or brick may eventually lose its original strength.Deteriorating wall reinforce the metal strapping.Fixed framework should take the full load of the glazing frame.

The video shows another way to strengthen the parapet.This is done using a cement-sand mortar.At the top of the parapet formwork is set small.

After pouring surface of the solution to align strictly horizontally.It is necessary to wait for the moment when the solution is completely cured.

Only then can continue to work on the glazing.In some cases, you can align the parapet, securing the top wooden beam.This solution is suited for glazing of loggias.

Installation visor

visor mounted along the top line of the next step after cleaning.That it is necessary to do before you attach the frame.

visor must be installed no matter what glazing - cold or warm - is performed on a particular balcony.This arrangement ensures the removal of rain water from the glass.

This video shows how important is the function of this simple element to the look.

Video:

Before starting the installation work is necessary to remove the glazing from the frame.This is done to ensure that in the process of fixing does not break the glass.

Since the peak has already been installed, the next step is to secure the lowest ebb.The resulting void between the parapet and the tide is filled with sealant.

next step - to an aluminum profile attached mounting plate.Fixing is performed by means of screws.The distance between the plates, it is desirable to maintain 7 cm.

The photo shows how the plate for mounting frame.

After that, you need to install the frame into the opening.The design should be fixed with wooden wedges and align.Alignment - critical operation and should perform well.

frame is aligned horizontally, vertically and in the plane of the balcony doorway.This is done in order to outline the walls and ceiling space, which will be drilled for the mounting elements.

After marking the holes have to be drilled and insert the plastic anchors.All these actions are carried out quietly with their hands.

attaching the frame, you need to double-check its orientation in space.Deviations from the vertical and horizontal should not exceed 3 mm.

When the frame is secured, in its place installed deaf and movable frame.Sliding sash should be easily removed and installed.When you move the effort is not necessary to apply.

If these conditions are not met, it means that design is skewed.It is necessary to examine it and make a payment again.

final stage

On the photo represented a balcony, just glazed aluminum profile.At the final step is to seal the mounting foam all the cracks and voids.

Places foaming and outside and on the inside must be closed nashchelnikami plastic.After the completion of finishing works on the frame mounted accessories.This is also a crucial moment.

Video:

all levers and knobs to adjust.Shutters on the guide should move smoothly and without squeaking.

For this movable parts should be lubricated with machine oil.