Build Daily

Equipment

August 12, 2017 18:06

Washing machine during the spin cycle hums why much buzzing , the causes and what to do

click fraud protection
Washing machine during the spin cycle hums
  • Why machine is very noisy - common causes
  • What should I do?
  • Prevention

Modern washing machines work very quiet compared with the first models, which is quite noisy, especially during the spin cycle.Now the appearance of extraneous sounds is considered a signal that the washing machine is not all right.If the device has become buzz during the spin cycle, you need to identify the cause immediately.Even when the problem is not serious, it is better to immediately remove.After all the buzz - it's annoying factor that prevents rest, and in addition, may cause trouble your neighbors.

In this article, we'll tell you about why the machine suddenly starts to buzz during the spin, and how to fix it.

Why machine is very noisy - common causes

list the most common causes of buzz.

Extraneous sounds during the spin cycle can occur in the following cases:

  • before using the washing machine you forget to unscrew the bolts that should fix the tank during transport unit;
  • worn or damaged one of the bearings;
  • into the cavity between the tub and the drum was a foreign object;
  • loose drive belt pulley mounted on the drum;
  • counterweights mounted on both sides of the tank, slightly recorded;
  • rubber collar slipped off the edge of the hatch, or it does not fit;
  • mistakes during installation of the washing machine.
Replacement of worn bearing washing machine , if it is buzzing during the spin cycle
Check and replacement of the cuff of the washing machine , if it creates noise during washing and spinning

What should I do?

If this is the forgotten bolts holding the tank, you just need to take them off.Typically, these springs are fixed bolts on which hangs tank.They are located at the rear of the washing machine and unscrewed wrench without a problem.

Transport bolts washing machine mo

If it's worn bearings, replace this item with the gland.To remove the bearing, it is necessary to disassemble the washer, remove the tank and remove the drum.To do this, read the article about how to replace the bearing in the washing machine or see a video tutorial on his replacement.

If the inside of the device objects have fallen , it is necessary to remove them so they do not damage the mechanism.For this stiralku just have to disassemble to inspect the tank and remove the obstacle.

Removing foreign objects which create noise in the washing machine

If this is the drum pulley, required to examine his mount and the integrity of the strap.The mount can loosen, and the drive belt - tear as a result of long-term operation of the unit.Instead, wear of the belt should buy a new one, and a weakened attachment pulley - tighten the improvised instruments.

If this is in contrast to, this problem is easy to fix.The counterweights are needed to process the spin washing machine vibrate less.If these items are faulty design, vibrations increase, whereby there is a drone.The most common damage that occurs with counterweights - a looseness.As in the previous case, the loosening of fasteners, simply tighten.

If fault rubber sleeve, would be best to replace it.However, there is a "popular" method of solving this problem.This is done by using a piece of sandpaper, which is placed between the lip seal and the front panel.Then, run the wash mode with an empty drum.After that, you need only remove nazhdachku and clean the drum by pieces of rubber and sandpaper.It is believed that in this way you can quickly align the poor quality cuff.

If you decide to replace all the same cuff, watch the following video, is how to do it.

If it is not a failure, and incorrect connection of the washing machine, it is necessary to dismantle all the connections and connect all over again, just follow the owner's manual.If you doubt that it will be able to properly connect to the sewer and water pipes, it is better to entrust this work to professionals.

Prevention

been eliminated buzz during the spin cycle, you need to make sure that background noise does not appear again.

To do this, try to follow the simple advice:

  • Do not overload the washing machine.Load the drum as kilograms of laundry, as calculated for the model, but no more.
  • Do not wash too often let his assistant to rest.Experts advise to run stiralku no more than once a day - one day she will have time to dry and "relax".Try
  • often wash at the highest temperature and with the highest number of revolutions.
  • Do not forget to periodically clean the drain filter.
  • Each time, before you download the laundry, check that there are not lost in the pockets or in the folds of the things small objects.
Overflowing washing machine is one of the reasons for the noisy work during the spin cycle
Laundry service at the highest possible speed and temperature for the prevention of work without noisy
Cleaning the washing machine filter quiet operation during the spin cycle

for periodic preventive maintenance scaling and lime.How can I prevent this, refer to the Ukrainian program "All bude good."

instagram viewer