How can I make the corners of the ceiling plinth ?

Installing plinth ceiling deal is quite simple until it's time until it does not go on how to make the corners of the ceiling moldings.

docked moldings on the corners - the most difficult in its installation, thus, if you make the wrong seam, the material will look ugly, and immediately spoil the impression of your fresh repair.

Standard junction 45 degrees are not always suitable for different types of rooms, and a cut angle exactly turns out is not the first time.

In this article you will find some tips on how to make the joint ceiling moldings to attach it exactly, as the sub video will help you to do it with their own hands, without damaging the material, and we'll show you how to glue the fittings onceiling.

Cropping accessories via Mitre

To trim angle for ceiling right the first time, many have resorted to the use ofthis tool - Mitre - which has long been a well-known and popular among those who make repairs on their own and want to cut skirting angles.

Mitre has the appearance of a small box equipped with slots.With it, you can cut corners ceiling moldings is at such an angle that you want.

miter box are made of metal, wood or plastic, and this - the simplest and most ancient device, with which you can cut pieces of wood, or in our case, cut hardware at an angle of 45 or 90 degrees.

release for home use the most basic model, the professional miter box to work in production are equipped with a turning mechanism that allows you to install and trim detail at any angle.

However, even the most simple miter box would be enough to cut the ceiling fittings for connections in the corners of rooms.

If such a tool you do not, then you can easily make it yourself.To do this, you need three cutting plywood or boards that have the same size.

first secure their deployed as the letter "P" and mark the corners, and then make the long slits with a hacksaw, following the layout made and fasten planks or plywood.

Then you need to take another measurement to determine the angle at which the plinth must be cut off.When this is done, put the bar in the miter box, referring to the position of hardware was the same as on the ceiling.

plinth should be strongly pressed to the other side of the miter box and lock it in this position.

ensure that the material is installed smoothly, you need to put the saw at 45 degrees in the opening provided and trim detail.So treated inner corner.

adjacent parts can be cut similarly, just trim it needs so that it mirrored the first.

Please note that if your skirting boards made of PVC or polystyrene, the internal junction of cut best with a hacksaw to work with the metal blade or a building, asthe edge in this case turn out smooth and neat.

to cut hardware correctly go ahead with its front part.

be slightly different technology, when to treat the outside corner.

first thing you need to know the distance from the nearest wall to the outer corner and lock it from the inside of the material (it is possible to write an ordinary pencil).

better to round the value in a big way, taking into account the fact that the fitting edge should protrude a few millimeters.When everything is ready, you need to hold down the material miter box and cut the unnecessary part.

adjacent parts is treated in a similar manner by simply rearranging its mirror image relative to the first.

Once this work is completed, and before you start gluing, have to dock parts - if everything is cut correctly, they should be ideally suited to each other.If

completely smooth interface did not work, it can be a little trim the edges of the material with a knife - in most cases this should help, and then docked becomes completely flat.

Watch a video on how to properly make and attach the plinth - this will save you from unnecessary costs and possible parts of marriage, as well as make the job much easier.

Video:

Trimming without tools

Fit straight corners in moldings can be and without the help of additional funds, using the method of marking.

to work you will need the following tools:

• line;
• stationery knife;
• area.

first step is to find out what size corner in the room - for this you need a corner.Attach it to the corner of the polotke, where it will be necessary to join the material.

size should be 90 degrees or have a value approximate to this, depending on how the correct shape is your room.

If the joints in the room do not meet this level, it means that they are not equal and hold the dock is a little more complicated right.

Once you have calculated the size, attach to the ceiling molding line at an angle of 45 degrees, and cut the unnecessary part of the material office knife.

to get butt smooth and clear, should be cut quickly and clearly, but do not press too hard on the accessories, otherwise it may be damaged.

If you want to make a joint of a wooden plinth, then use a knife instead of a hacksaw or jigsaw, cut and place draw a pencil to make it clearly visible.

Before gluing corners, make sure that they obtain flat: it is necessary to attach them to their dock and connect at a single point.

properly trimmed baseboards should ideally be connected, without seams or irregularities.

If you find that the joints of the walls in the room are uneven, you must first find out their degree, and then divide this by the two - so you know what angle you need to cut off part of the accessories.

example, if the joint is inclined ceiling 80 degrees, the ceiling trim moldings need angle in

40. Just as in the case of using a miter box, slightly uneven corners can again independently gash walk along the edge or sandpaperthat can align several docking surface and make better.

Then apply again the plinth to the joint - after re-treatment, they should converge better.

To make the angle right the first time, watch the video from the stage.

Video:

In fact, there is nothing difficult, the main thing - to calculate the size of the angle of the ceiling, as well as the angle at which to cut the plinth to obtain a flat joints.

the easiest option - to "close" the joint special fittings, however, this is only possible with external corners of the room.

Such accessories are sold in all DIY stores, and if space allows the device to you, you can choose this option, and do not engage in self-docking baseboards.

This is especially true if the corners of your apartment rough, and join them pretty hard.

Installation material

course, properly trimmed and washed down baseboards at the joints - this is the most important stage in the work, but it is important and correct them stick, or even with smooth corners ceiling moldings will look sloppy and ruin the repair.

Gluing always start with the corners - it's easier to keep track of exactly how to go to the material, plus it's just more convenient, becausethe size of the segment direct plinth trim is easier than customized accessories not only by the size of the angle, but also under the already pasted ceiling moldings.

If you paste material into the joints correctly, then the rest of the plinth is also no problem.

Video:

Before gluing ceiling moldings, it is necessary to prepare the surface.Do this by using a primer, with a simpler version of repair, you can simply moisten the surface with water sponge.

Processing provides better grip material, which significantly facilitates the work, asfittings immediately grabs tightly to the surface, and will not move away and fall off.

first thing you need to put on a plinth glue or putty composition depending on what material you choose to work.

If putty, then it is processed not only back, but the exterior of the hardware, but the band must be narrow enough to avoid too much glue.

before applying the adhesive spend another pre-dock and make sure that the material is connected smoothly, without cracks and gaps.

After this process the adhesive first part of the details and press it to the ceiling.Then you need to dock the second part of the corner.

to hitch baseboards and ceiling took place is better not to glue the material immediately after application and wait a bit to grab the glue had.

If you want to decorate a plinth rounded corners, the material is first cut into several pieces and then turn glued to the desired surface.

little different is the case with wood moldings - they are usually bolted with screws, but do not put on the glue.

This means that the correctness of connections should be taken even more closely, because redo the work after they are installed in a different way to connect the plinth will be impossible.

If in spite of all your measurements and docking, you notice that after stickers ceiling moldings in the corners there were still gaps or irregularities, use sealant to eliminate them.

White Sealant is virtually invisible on the baseboard, especially if you hold a job carefully.

Once you have pasted accessories, clean place with a sponge or just hand to smooth seams and remove the remnants of funds.

Video:

Once angles are ready, you're ready to finish the rest of the surface.This is an instruction how to install ceiling moldings in the corners.

This job will require you some care, but generally is not a big deal.

Use video instructions - they will help you not only the right to cut the plinth, but also to set them so that there was no irregularities and gaps and do not have to redo the work in the future.