Step by step instructions for connecting electric hob

theoretical part.

So, electric cooktop is connected to an outlet specially otvetvlёnnoy high level ground with a capacity of 32 to 40 A. With regard to the wires - they should be copper, with three conductors have a cross section of not less than four millimeters.Today, however, the wiring harness designed for connecting cables and chetyrёhzhilnyh.Speaking of the outlets, which are designed for connection of cooktops, they are classified as follows:

• three-pin;
• chetyrёhkontaktnye.

Of course, if you have already finished the plug, then connect the electrical panel is greatly simplified.But for that to connect the wire to the power outlet, you need to know the specifics of this particular process.Assume that the power of the cooking stove has 4 conductors (phase, phase, zero earth), in the wall of the 3. This indicates that the stove requires a jumper between phases on the terminal board to connect to the three-wire cable.

Then proceed as follows: between black and brown copper wire set jumper that usually comes, and then we connect one phase to the phase conductor of the residential wiring (must be black, brown, white colors).As for the live and ground zero, they remain intact.

The resulting string needs to be isolated.If the wires out of the wall have the same color coding, then using a multimeter, determine where the zero and phase.

This is important!Sockets, which are going to connect the electric hob, pre-disassemble and inspect, because in some cases there is a discrepancy between the contacts and the tile wire, causing such that outlet may occur after connecting the sparks begin to melt.

strong recommendation

Consider the following tips for connecting the equipment with his own hands:

1. Before you connect an electric hob, you must install an RCDand the machine.Picked it as follows: 16 A sockets require the switch 25 A and 20 A - from 40 A. Absolutely can not use the machine to more than one device.
2. housing must be grounded, but not to the conductor of the other equipment, and with the conductors that are connected to the terminals of the socket.Most of manufacturers offer models that already have a protective grounding bus, which only need to be connected to the wires of the apartment ground wiring.

Induction Cookers

induction hob or oven, installation of which we have already mentioned, you can connect almost similar to the electrical panel of the cooking.Make sure that there is no fundamental difference, reading tips listed below, where we tell you about the connection plate.

1. cords are three-core and four-core.If you decide to connect the electric panel the cooking, it is better to buy a power cord that is suitable for kitchen sockets designed for 220 or 240 volts.
2. Next, open the access panel.For this we need to find on the back of the box cookers, metal plate hidden.Using a screwdriver, unscrew it.
3. removing a metal plate, locate the terminal.First, insert the cable clamp in the hole.The cord should be withheld due to the use of clips.This must be done so as not fallen electric wire.Next, run the cord through the cable clamp.Wait with tightening screws.
4. If we want to connect the oven outdated sample and there we find the 3 wires.In recent models, there should be 4: 2 - phase 1 - neutral, 1 - ground.Location of this: in the center is the neutral point, with its two sides - the phase delays, under it - the grounding point.Before interconnect wires, make sure whether there is a copper strip, which usually connects the grounding conductor to the neutral.Seeing elementary eliminate it.Phases need to be bridged, as we said above for connecting electric hob instructions.
5. necessary process when connected to the electrical panel of the cooking is to combine strings.Of these, black and red - phase wire, green - and blue earth - neutral.Before connecting wires, unscrew the connection point, and instead connect the wire.First connect the green, followed by blue cord, then the remaining (red or brown on the bridge).
6. then make sure that the cord is stretched.It is undesirable for it to be twisted or hanging.
7. difference electrical panel boards of gas is that for the first control scheme, you must have a computer, which is available in the latest generation technology.

Note whether the connection is firmly carried out, or can not stand the machine, and you have to repair not only the device, but also all the wiring.It should also be noted that the electrical installation of the hob can be produced without the plug directly to the network.To do this, you need to bring a separate line from the junction box.

In this article we lucidly explained to you how to connect an electric hob self.We hope that you will be properly perform the tasks and achieve a positive result.

Also read:

• set of tools for electrician
• How to make ground in
• apartment Why triggered circuit breaker