Shpaklyuem plasterboard before painting

Perform ceiling plaster of drywall for painting should be subject to certain rules and regulations.

As you know, all the defects that are present on any basis, will strongly visible in the case of his paint.

That is why, in order to avoid low-quality execution of work and to remove all possible roughness, the surface should be prepared in a special way, namely, to hold her luting.

In the event that all the work carried out correctly, subsequent painting will take place without any problems and the ceiling will get an attractive appearance for years to come.

worth noting that the filler helps to maximize hide all defects and irregularities existing on the ground.

This work is performed on the same principle as for good measure, and for multi-level ceiling, made of gipsokortona.

In any case, with the right approach to business and the minimum skills building plaster ceiling is done with his own hands without assistance.

For more information about how to prepare for painting the ceiling with his hands, told in the video, which is available below.

Video:

Features of work

before on the base surface of the drywallapply finishing coating, called finishing, it must be a special way to handle using special leveling compounds.

In this case, the leveling compound acts as filler, which must be applied as a two-level, and on a solid ceiling, which is built using drywall.

Currently, there are several different types of fillers, which can be divided among themselves on the starting and finishing compositions.

addition, this decoration material is different to each other and on the composition, namely the components which make up its foundation.

an important role in conducting putty base, collected gypsum board, playing primer, which makes the surface more suited for the application of the basic structure.

Almost all lineups in finished form are dense, similar to sour cream mixture.

In most cases, their main purpose - is to remove all the strong differences that may be present on the surface of the base.Also

via incorporation of this mixture is made different technical holes and cracks.

If necessary, the starting material may be applied in several layers, each layer must be thoroughly dry before applying the next.

In some individual cases, it can be placed under the reinforcing mesh, which makes the base of the drywall stronger.

Video:

In turn, finishing compositions have a liquid structure that allows us to base surface is practically perfect and smooth as possible.The main purpose of this mix - this is to give the base a smooth shape, so it is necessary to apply a thin layer.

Preparations

Plastered ceiling, which was assembled of drywall, is the final stage of work in front of his painting, which should be treated with full responsibility.

In order to do all the work with his own hands, it is necessary to prepare an appropriate tool and the material.

Primarily need putty itself, as well as suitable primer compositions.You should also have on hand a special mixer, float and putty knives.

In the first phase of work will be necessary to properly prepare the surface of the ceiling.

For this purpose, it should remove all dust and dirt, as well as see to it that full, there were no irregularities.Thereafter, the entire surface of the ceiling should be thoroughly primed.

This is done in order to grip the base mixture and drywall to be as durable as possible.It is better that the work is done by using an ordinary roller.

After the ceiling, assembled from drywall, after priming the well is dry, you can proceed to the next stage of work.

should now place all gypsum board joints strengthened with a special reinforcing tape.

is especially significant for multi-level ceiling, which consists of a large number of changes, respectively, has a plurality of joints.

In order to secure the reinforcing tape on the ceiling, a small amount of the solution must be applied to the junction, then drown it in the very tape.

When installing the tape should be especially careful to see to it that it fell as straight as possible, without any distortions.

This work should be done with every seam, then you need to allow time for it to dry out the seams well.After that you should carefully remove the tape from all the hardened pieces of the solution.

starter layer

main purpose filler - to hide it before painting the ceiling all the irregularities and defects.

When applying the starting material layer, it is important that you can not miss out on the surface of the ceiling is no plot.Otherwise, after the painting may occur serious defects.

The room in which you are puttying ceiling plasterboard collected, should be to ensure sufficient coverage.

This will visually observe even the smallest defects.

If putty is applied in several layers, each of which is necessary to allow time for drying of, and only then apply the next.

For ceiling spackling mixture is recommended to plant in small quantities.This is due primarily to the fact that the composition dries quickly and can simply not have time to develop it fully.

Particular attention puttying plasterboard ceiling should be given to those places in which the mounting plates to the frame.

filler layer should be as thin as possible and free from smudges, so how to fix them after drying your hands is quite difficult.

Apply the mixture with a spatula should be first along the ceiling surface, and then from side to side while keeping an eye to the grooves of the screws were filled as tightly as possible.

Video:

Particular attention should be paid to sealing of corner joints, and this work should be carried out in two stages.

to start processing one side of the angle, and only after it dries, puttied second.Thus treated the entire surface of the ceiling plasterboard collected.

For more information about how to perform the plaster ceiling of plasterboard, described in the video, which is available above.

final milestone

To surface acquired a perfect flatness and maximum smoothness, performed finishing putty.

After this phase of works plasterboard can be painted in your preferred color.The work should be done carefully, taking care to avoid any flaws and defect formation.

for finishing putty is best to use a wide spatula, while used in the mixture should resemble a kind of thick cream.

When applying putty is necessary to ensure that the layer is laid down as uniformly as possible, and was as thin as possible.

When executing spackling drywall work surface finish mixture should not be anywhere to hurry, because the quality of the work must be beyond reproach.

To finish layer of putty has got a good grip on the basis of plasterboard, and in addition, has become as smooth as possible, it is done cleaning with a special mesh construction or fine sandpaper.

same way corrected all defects and irregularities committed during work.

It should be borne in mind that the surface of the drywall sanding is done only after finishing putty dries well and will get a good grip with the ground.

In any case, at the end of work on the putty ceiling plasterboard, its entire surface needs to happen not only smooth, but smooth.

Caulking gypsum base must be carried out only with quality compositions.

Video:

When working keep in mind that how the base coat is made of drywall, largely depends on the appearance of the surface, even after painting.

slightest defect and shortcoming necessarily manifest itself later, and spoil the overall appearance of the base view.

With the right approach to business and compliance workflow technology, gypsum plaster base can be performed independently.