Step by step instructions for installation of sliding gates with their hands

There are several types of gate performance, so the choice of a particular type of structure depends on the owner's preferences.Traditionally considered as swing, it is most often used in the construction of various objects (described here).But according to experts, it is now beginning construction recoiling greater demand.

can distinguish two kinds of such gates - rail and cantilever.The first type is now virtually established, as it is associated with certain difficulties in installation, and deficiencies in these structures (in practical terms) missing.For example, the need to constantly to maintain (clean) the rail in size limitation entering vehicles and a number of others.

therefore focus on sliding gates cantilever.They are much more convenient in terms of both installation and subsequent operation.

Features

• Can be installed in any location, as there are no restrictions on the size of free space in front of them.
• In such gates could enter the car of any height, if appropriate design features to consider in advance.
• Ease of use.For example, there is no difficulty in opening / closing at strong gusts (unlike swing).
• versatility.Depending on the specifics of operation, you can choose any size of canvas.Gates may be light weighted - a lot of options.
• A variety of exterior trim.To this end, commonly used materials, such as sandwich panels, corrugated, wood, metal profile.
• Attractive appearance - an additional "plus" in such structures.

It is clear that the cost of this type of gate depends on many factors (size, materials, and the like), so we only indicate the approximate price range - from 55 000 to 130 000 rubles.With this in mind, it makes sense to build such a structure on their own.

technology

dwell only on some of the features as the nuances of civil works is no sense to paint.

scheme

Everyone develops a drawing, based on local conditions.Please note that it is not necessary to make such massive gates too.This is reflected in the rise in price of construction, primarily due to the foundation.

Depending on which side of the house there are the gates, to choose the direction of their rollback.Thus it is necessary to take into account the availability of free space to move the canvas horizontally.

counterweight - half the width of the opening.

Height advice is - just below the fence (about 10 cm).But the extreme poles should be a little above it to rise.

Components (materials)

Self fabric can be manufactured, pick a channel base, e / motor for driving.Much more difficult with the rollers.It is better to buy them, and set.They sell 3 varieties.Advice on buying the following:

• set high - if the fabric weight more than 600 kg, or a length of fabric more than 6 meters, but it is not necessary for a private house..Price - about 38 000 rubles.
• average.When the parameters 4 to 6 m or 400 - 600 kg.About 23 000 rubles.
• small - up to 400 kg or 4 m About 10 -. 12 thousand.

profiled tube on the frame for webs (60 x 40 sufficient wall thickness 2 mm), and the remaining materials - depending on the selection and circuitry.

It is worth to stop the engine.His power is calculated not only based on the weight of the gate (in the assembly).It is also necessary to take into account the likelihood of a glacial surface in the winter.Consequently, the total mass of the moving parts of the structure will be increased.

Construction foundation

This is nothing new.In depth, it should exceed the level of soil freezing in the region.

done first frame (open U-bar).Mounting depth of its "pillars" - not less than 1.5 m (to ensure a secure fit of the whole structure).According to the width of the trench is dug foundation sill.After setting the carcass in the ground the upper part will be "lower edge" of the entire structure ( "zero").

When assembling the frame, check its compliance with the longitudinal axis of the fence line.Cabling for the drive power is performed before pouring the concrete solution.

fabric Manufacturing

It is necessary to make internal stiffeners.In fact, such a structure (frame) is not much different from the crates, which is arranged at a wall covering.The difference - 2 extreme (carriers) "legs".

Preparing for the Build gates

necessary to fix the carriers' carts. "The front is placed approximately 15 cm from the edge of the opening.At the place they are fixed by welding.

All other activities on placement and installation of additional elements fabric depend on the specific design of the gate.