Repair of plastic windows with their hands

Sooner or later, every property owner in which fitted plastic windows faced with the need to repair them.Approximately 5 years after starting a little loose any, even the expensive hardware.If insufficient care can begin to crumble seal.Glass can beat the younger generation.And pressing the adjustment should be carried out 2 times a year.In this article we'll show you how to make repair of plastic windows with their hands.

Repair broken handle

Most often the first break when the handle reinforced plastic window operation.It often happens that during operation window sags tenants and instead to adjust the slack begin transom firmly pressed against the frame by acting on the handle.The handle, of course, from such actions may break or just stop turning.

If there was such a disaster in the first place need to find and eliminate the cause of the failure, and then adjust or replace the handle itself.To do this, turn the plate covering the fasteners 90 degrees.There will have to act according to the degree of breakage.If you just need to pull the handle is loose, you need to pull the screws with a screwdriver.If you plan on replacing the handle, the screws need to unscrew the handle comes off easily and in its place establish a new pen.This procedure is the repair of plastic windows with their hands will take the strength of minutes 15.

Adjustment clamp PVC windows

Clamp is usually adjusted with the change of season.In winter, it attracted to the transom frame denser the summer weakened.In no case can not be left for the summer winter clamp, because it will lead to the destruction of the seal due to excessive load.Adjusting the clamping plastic window occurs each brand differently.

example, for self-adjustment ROTO fittings need furniture 6 Allen key.Along the perimeter of the transom need to see where the locking pins.Each pin has a notch.To adjust for the winter notching needs to look in the side streets to adjust for the summer - in the side of the room.For more information, see the article about the adjustment of plastic windows.

Replacement seal with your hands

For seal plastic window should be maintained at least 2 times a year.In spring and autumn it should be cleaned with a wet cloth and detergent can be from dust and dirt with silicone oil.If you do not perform this procedure, the seal begins to crumble, disintegrate, affecting heat-saving characteristics of the plastic window.

seal sold in building supermarkets.When you purchase is necessary to take into account that on the window seal loop 2: internal and external (on the leaf and on the frame).Both need a tape measure.After buying a new carefully removed old, along its length, you can cut the length of the new.Wash the window under the old seal.Top-down start to insert the seal into their grooves, pressing it to any suitable tool, such as the reverse side of the scissors.Especially stretch material is not necessary.The joints are glued seal.This kind of repair of plastic windows, you can easily make your own hands.To do this, you can read the article about the replacement of the seal on the plastic windows.

Repair (replacement) of accessories

most commonly required accessories adjustment slack folds.When sagging leaf starts opening / closing to touch the frame.It will take control of main units, which is a little different from each manufacturer.At any eccentric on the leaf is written the name of the hardware manufacturer.The most common ROTO, Siegenia-aubi, Maco.On the manufacturer's website is easy to find step by step instructions on the repairs of PVC windows mean.

Replacing broken glass

If one broken glass in the pane, you still need to change completely glazed assembly.Perhaps this is the most expensive kind of repair of plastic windows, so for those who want to save, it is better to do it with their own hands.For a start you have to order a glazed in the factory or in a specialized firm.To measure the glazing do not need to pull out enough to measure the distance between the extreme points of clamping glazing beads and subtracted from each result by half a centimeter.According to these parameters, and you can order a new glass unit.

To remove the old glass is first removed with a chisel long vertical glazing beads.Remove the fillet should start from the corner.Gaskets should be retained for the new glass.After removing the glazing beads, glazing easily pulled out, and the frame is washed with soap and water.You can now install the new double-glazed and re - glazing beads in the reverse order.Glazing beads are inserted into grooves of light strikes a rubber mallet.More details all painted in the article about the replacement of glass with their hands.

Now you see, that independent repair of plastic windows - scary procedure.Video and photo repair of plastic windows with their hands to help you perform all necessary operations.