Take readings from meters Mercury, Micron , Energomera

old-fashioned models

If you are in an apartment or house on a pole mounted inductive energy meter - on the front panel turns the disk data removal is not a big deal.You must at one and the same day of each month to write indications on the leaf.Further, all very simple - from the existing value, you must subtract the number that you have written in the past month.As a result, you should get a monthly consumption of electricity.However, this procedure does not remove the data ends.

very important point, which is a bit simplify the withdrawal process - you have to take readings at the counter just before the decimal point.The latter figure, which is highlighted in a different color (usually red, as shown in the photo), is not considered.If we look at a visual example of how to remove the monthly consumption, according to the photo you should prescribe 000004 kilowatt / hour (excluding the last four).

Then all depends on how the payment is made in respect of electricity to your service organization.Or, you just pass a few readings in the organization, or you count the amount of self-payment and pay it on the receipt.In the latter case, you need your captured value multiplied by the tariff, which you are using.

new sample

Models In modern electronic counters are no longer used rotating drives and mechanical dials.electronic display is already installed in these models of electricity, which in addition to the general indications kW / h can display time, accounting for a certain time of day rate, etc.All these innovations really allow power consumption will stay for a month and at the same time to view other equally important indication.

At first glance it may seem that with such a mini-computer will be difficult to take readings of electricity per month, but it is not.Everything is much easier than you think.So, to remove the data you need to perform a few simple steps:

1. Press "Enter" (you may have to click several times to find a suitable option).
2. If you have one-tariff electric meter, write down the value of T1, two-tariff - T1 and T2, trehtarifny - T1, T2 and T3.
3. take away from the existing values ​​of the same in the previous month.
4. take readings pass in the service organization or independently calculate the amount to pay.Here we must bear in mind that if you have a power meter to two or three tariffs, each value (T1, T2, T3) to be multiplied by a coefficient, which is indicated on the receipt.

By analogy with the example of a video, you can record the data from the device 200 Mercury, Micron, Cascade, Energomera, Neva Lane and Electro.On the pros and cons of dual-rate counters we talked in the corresponding article.With proper use of household appliances electricity meters are an order of magnitude more profitable conventional models!

you need to know!

1. If the meter count went to the second round, that is, if it is zeroed out, remove the power readings should be as follows: add the number to an existing unit in front and take the value of the preceding month.For example, if you have a five-digit display (without decimal places) which displays 00033 (as pictured below) after a reset, you must add a "1" on the left.As a result, the number 100033 is necessary to take away the old reading in the past month, for example, 99,916 kW / h.Concluding the same example you should be able to 117 kW / h (100033-99916).By analogy, you can take readings of the six-digit or four-digit power meter.
2. If no mechanical scoreboard comma, as in the photo below (model Energomera CE6803B), and you have difficulty removing the data from the past month, there are two out of the situation.Better, of course, immediately check with the company that installed electricity meter, how to remove the monthly reading of electricity.But if you forget the master himself and to clarify this point, the visual look at the front panel.Tenth share of electricity consumption should be highlighted in a different color - red, if there is no point.In the event that there is no visual separation, so you need to remove all 4 or 5 digits and written in the receipt.
3. Reading the three-phase electricity meter is different from a single-phase model.You only have to write down all the numbers after the decimal point, and take away from last month's values.
4. If you are in the house or apartment features a modern counter the new model - the electronic, testimony to the service company can be transferred automatically - remotely.In this case, you do not need every month to remove the meter data, asreceipt itself will come to the address.The automated system of control and readout, called AMR is very convenient, especially if you have a multi-tariff electricity meter.

As you can see, most consider the monthly electricity consumption is not difficult and it does not matter, one-tariff electric meter you have, or multirate, single-phase or three-phase, electronic or induction.We hope that the material was understandable for you and now you know how to take readings of the meter.Recommended view provided by video examples that show instructions for removing the data with your own hands!

Also read:

• How to stop the electric meter magnet
• How much electricity consumed warm floor
• How to pay less for electricity legally