The algorithm works on installation of baths : step by step

bath Dismantling may need owner of the premises in 2 cases:

1) Sanitary Products cracked or fallen into disrepair (there were abrasions, cracks and chips);

2) being overhauled with full replacement of plumbing and trim surfaces.

Expose the old bath, especially the first time, is quite difficult.There its technology this operation.Below is a step by step plan of action.

Preparation tool and flat

Master in dismantling the volume of sanitary products require the following set of tools and accessories:

• Cutter;
• Screwdriver;
• chisel;
• Wrench;
• Carpenter hammer;
• Rags;
• Hacksaw for metal works;
• Sledgehammer.

From the bathroom facilities removed other plumbing products together with accessories (shower hose and mixer, sink siphon, etc.).Cabinets, shelves, laundry baskets and other little things taken out first.If the bath is combined with the toilet, the toilet is also dismantled and taken out for the duration of the work to another room.

next stage of preparation "battlefield" - the protection of the door leaf.Ideally, it should also be removed and endure.If this is not possible, the door surface is well protected by any material with high strength properties.

All preparations bathroom to the dismantling of the old cast-iron or steel (can - acrylic, marble, etc.) the product is complete.

Successive operations on removal and removal bath

First disconnect the pipe supplying water.Particular attention should be drained, stretching into the sewer system.If the bathtub during the existence of the Union, with a drain junction is often held together, so the only solution would be cutting the tube hacksaw.

Modern locksmiths and plumbers use adapters, couplings and other plastic parts.Therefore, dismantling happen quickly, you just unscrew fasteners and remove the drain pipe.

Important: at the opening of the pipe leading to the sewer riser, bad odors will spread throughout the room."Fragrance" can close the old cloth tucked into the socket prepared in advance with a cloth.

next step - to remove the products subject to the dismantling of the bathroom wall.Most often, the connection is firmly fixed tile or other finishing materials.Using a hammer and chisel lining material strays.It is important to be careful - too strong blows on the wall can lead to its destruction.

Then you can move on to the examination of the bath fixtures to the floor.Many owners protect their old cast iron products screens to improve the aesthetic appearance of the room.If the screen is paved with ceramic tiles, it will also need to disassemble.Plastic or wooden screen design simply dismantled using a hammer and chisel.By the way, you can not hesitate and make an effort at the stage of destruction tiled screen, so you can access more quickly to the floor.

bath installation option - that are interested in the master in the next phase of work.When cementing legs straight into the screed of concrete will have to destroy the last hammer.In fixing legs plumbing bolts fasteners need to unscrew.The lower the operating bath life, the more likely the master disconnect it from the floor quickly and power costs.If the bathtub is in place for decades, all of its long-rusted bolts - have cut the legs of a special tool - hacksaw.

Important: When sawing the legs with iron plumbing at the opposite end it is necessary to substitute something or ask a helper to hold the product.Otherwise, heavy construction may fall upright master, causing injury.

next step - the rise of the bath, which is invited to another man, or a pair of helpers.Weight of cast iron plumbing is very impressive, but it will have to put the upright to the wall opposite the tap location.In no case can not rely on a bath towel rack, if it is located on the right wall, will have to come up with a design for the old plumbing elsewhere.The reason - the design can greatly damage the functional device, scratching enamel or pognuv pipe.

Next on technology products bring down all the remnants of the solution, coatings and rust.After that, with the help of 2-3 persons bath is removed from the premises where it was installed.When you pass through the door you need to watch out for in order to avoid damaging the jamb and the door leaf.Sometimes a bath is necessary to turn a certain angle - it happens in small apartments.Following these steps is successful completion of the operation called "dismantling of the bath with his hands."

vacate the premises can be repaired on, and Marked bath or ejected, or waiting for the end of the repair work to reverse the installation (which is rare).Most often disused plumbing is sent to landfill or exported to the suburban area.

few tips to implement dismantling plumbing

The successful dismantling plumbing own hands must adhere to the following guidelines:

1. while taking out of the bathroom means of sanitary wares of acrylic algorithm works will be the same, but with one difference - added operation to remove bathloops.The procedure is not difficult, but necessary;
2. pulls If plumbing is subsequently set back, all the action with a hammer, a chisel, a hammer and a chisel must be performed very carefully.The reason - the risk of damage to the product;
3. All fasteners, which bath was attached to the floor, must be maintained.It is a well-preserved details of which can be re-used when installing the product shot back.

described algorithm works is strictly regulated.Subject to the sequence of actions baths dismantling will take place quickly and successfully.