How to install the lift gate to the garage with his hands

We are accustomed to the traditional performance of the valves garage doors - hinged type.However, overhead gates are becoming increasingly popular.Those who daily uses the machine and the value of time, consider them more comfortable.

They are different design features, and can be of several types.Rolling rarely used, so it makes no sense to dwell on them.The most common models of overhead doors for garages are sectioned and whole (tilt-up).

At first they consist of several sections (40 - 60 cm) in length, in which the frame can be stacked panels of different materials: metal, plastic, even wood.Joints between them are sealed + produced additional insulation.Bond component parts - hinge.

up-and-construction are more reliable (in terms of safety of the garage) and are considered to be the most convenient from the point of view of self-production.

But the general principle of the same.During the opening of the garage gate wing rises up to the ceiling, which saves space.

It should never specify that engage in the manufacture of lifting doors with "zero" experts do not advise.This is due to many complications, including, and in the calculations.Mainly, anticipated loads, spring sizes (or balances) and many other "nuances".Another important factor is how reliable mechanism for fixing the flap in position.

therefore expedient to use the elements of factory manufacture and assemble them yourself.Especially as a specialized organization, even if the products are purchased and it sets the gate for a fee.Mounting the entire structure can be up to 10 - 12 thousand rubles, and the price for the installation of the elements of mechanics and automation - from 3 600 rubles, depending on the "bells and whistles".Therefore, if you put yourself, you can well spare.

Different manufacturers offer many variants of the gate, which differ in many respects.Each kit necessarily included installation instructions.However, sometimes it some points that the future owner should know can not be reflected.And the criteria for selecting the model should also be indicated.

What to look

frame design (frame)

better metal frame than wood.Some types of gates have a gate, but such a "model" will complicate not only the assembly, but further exploitation.While on the other hand, if the car in winter is "laid up", the heat loss will be reduced significantly, because in order to get into the garage (for example, to go down to the cellar), do not have to raise the entire flap.On the gate insulation read in this article.But

gate leads to higher prices, and the sum comes out decent - 10 - 14 thousand rubles.

Fixing guides

Take into account that the weight of the lift gate leaf is quite significant.In addition, the dynamics (opening / closing) will create additional axial loads.Therefore, by fixing the guide elements depends not only on the reliability of actuation mechanisms, but also personal security.

tilt-model is considered preferable.And not just in terms of premises security.Available sections suggests their connection joints.Consequently, there is a risk of a failure of one of the fixtures.In other words, the gates Sectional less reliable in terms of intensive use.

panel

gate leaf should at closing firmly (tightly) cover the entire opening.It is necessary not only to prevent unauthorized penetration, but also to maintain a certain climate.This is one way to extend the life of the car without any repairs.In addition, we must not forget about the cellar, which is practically in every garage.

Materials

All loads structural elements are made of metal that is resistant to corrosion, or subjected to a thorough treatment of corrosion preventive compounds.Couplings, rollers - plastic + steel allowed.

Mechanics

Manual drive cheapens the overall cost of the set for about 4 - 5 000 rubles.It is less convenient, but more reliable.The probability of failure is minimal.The mechanism of joint-single control is preferable since it is more practical.

The design of the counterweight should be chosen for large panel sizes (and hence its impressive weight).

What envisaged

Maintainability

That failure is inevitable over time - it is clear.However, not every mechanism beyond repair.Sometimes it happens that you have to change the entire assembly or a single node, and this goes in the "penny."

In addition, there is an opportunity to acquire new hardware?What, where, time of delivery?The question is not idle.

Warranty terms

First , whether there is in general, and for how long spread?

Second , canceled under what conditions?This is an important detail.Is the gate self-assembly in violation of its terms?

What can save

• on the size of the canvas.
• The outer design.For more coverage, fashionable colors involve increasing the final cost.