How to make a self-leveling floor on a wooden floor

In the modern repair is often used self-leveling floors for leveling the base and topcoat.The main advantages of such floors are their durability, wear resistance, durability and ease of installation.In addition, it should be noted their ekologichnst and safety.Today, self-leveling floors qualitatively changed greatly in comparison with those that have been on the market a few years ago.An example of this is the 3d floor, which can be called the real masterpieces, thanks to unique design with three-dimensional image of an object.

Laying self-leveling mixture on a concrete foundation, no one is difficult, but how to do self-leveling floor on a wooden floor?After all, not everyone likes the prospect of the dismantling of the old plank floor.And if it is a private home, where the floor is initially completely wooden?It does not matter.There is the possibility of laying a floor filler and on a wooden surface under certain conditions.It is important that the old ground was still decent, and the mixture was tonkonalivnoy floor, so as not to reduce the height of the ceilings.

Preparation of the base under the floor of the inlet fill

Since self-leveling mixture should be poured onto the prepared substrate is sufficient, the process should be given greater attention.Any cause requires careful preparation.This applies particularly to the old wooden floor.Immediately make a reservation, that the old floor must be rotten, should not it come from any scratches, not to mention the presence of loose boards.

primarily made to dismantle all the baseboards in the room.After that, with the help of machines Scraping carefully tear off the top colored layer planks.Further, the grinding machine will be overwritten by the base, revealing cracks which necessarily have any old wooden surface.These cracks, bumps and cracks between the boards daubed using putty.For further work wait until it dries well.Then, using a coarse sandpaper, rub clean the entire surface.This technique will provide better adhesion of self-leveling mixture with a base.

nipped and even surface with a vacuum cleaner is cleaned of dust and degreased.Then the surface is sure to be primed.This ensures excellent adhesion of the polyurethane mixture with the wood.This should be done in at least two layers.The composition of the primer should add sifted quartz sand.Grains of this substance creates roughness of the base surface, which increases the adhesion area, and creates it in different directions.In total this gives greater adhesion polymer and wood.

tools necessary to perform the work

for the production of works on preparation of a wooden base and pouring the mixture will need:

• Average claw hammer, chisel and wooden wedges for removing the baseboards.
• Scraping machine or hand cycle.
• sander.
• Coarse sandpaper or emery.
• industrial or household vacuum cleaner.
• Roller or medium size brush to apply the primer.
• flat brush or paint roller with short nap for a uniform distribution of the polymer coating.
• Needle roller to remove air from the polymer coating.
• doctor blade and a metal spatula.
• Building mixer or a drill with paddle mixing the polymer solution sex.

Do not forget about these compulsory subjects, as safety goggles, overalls, gloves and respirators.In order to be able to move if necessary, on the freshly applied layer of self-leveling floor without fear, you need to get a shoe equipped with a sole with studs.

technology device self-leveling polymeric floor

technology itself pouring self-leveling mix on an ordinary wooden floor does not differ from a similar procedure, which serves as the basis for concrete.Differences concluded only in the initial preparatory phase, which we have considered in sufficient detail above.

Before filling the floor of the polymer must be very carefully read the instructions for the preparation of the solution, which is available on the packaging.A solution is needed to prepare to meet strict with her.

Take the dry mix from the bag and poured it into a convenient container for mixing.Very good may come from the plastic bucket with water-based paint.The powder is poured into the required amount of water according to the instructions and start to stir the building mixer or a drill with a special nozzle.Stir until the mixture until a homogeneous mass.Then, the solution was ready to spread on the prepared wooden base.Doing this will begin with the farthest corner of the room, gradually moving toward the door.

poured mass as it moves align with a spatula to obtain a layer of no more than 5 mm thick.This is the optimum size in the case of a wooden base.The final alignment and the removal of air bubbles produced by a rubber needle roller.In this case the room can be navigated using studded shoes.

Self-polymer mixture for a floor very quickly hardens, so the party solution should be prepared quickly.Fills gaps between them should be less than 10 minutes.It is advisable to pour a floor together using two containers.While one person prepares a mixture, the second fills and smooths the previous batch.The joints between the parties is pouring more carefully laminating roller, if you do the floor alone and continuous process can not provide.

15 minutes after the complete filling of the room you need to cover the entire surface of the film.This is required to ensure that the floor is not dust settled, spoiling the quality of the glossy surface.When the self-leveling floor is completely dry and it will be possible to walk, there is the possibility of applying the finishing coat.This can be a three-dimensional polymer flooring, paint or traditional flooring options.

cost

installation costs for the installation of self-leveling floors in the house are strictly individual.They depend on the type of self-leveling compounds, its manufacturer, on decoration costs.The floors in 3d format with exclusive patterns are much higher than ordinary.the wooden base of the device technology is self-leveling floor is not particularly complicated, so work can be done independently.This would provide a significant cost reduction in all repairs.

That's about to perform works prices by professionals in stages:

• Preparing wooden base to the filling polymeric self-leveling floor (average price of $ 5 per 1 square meter).
• primer prepared by the base (the average price of 3 USD per 1 sq m).
• Fill the wooden surface of the polymer self-leveling mixture (the average price of 6 USD per 1 sq m).

Thus for the full range of self-leveling floor poured, for example, in a room of 20 m2, you will have to pay 280 USDAgree that the sum of this quite impressive.It is much more than the cost of the mixture itself.All these prices are normal floor, which can be done independently.

Cost fill decorative floors are usually calculated individually.If you decide to make at home self-leveling floor in 3d format, there has necessarily need to use the services of a specialist.This will ensure:

• create high quality decorative coating.
• Warranty on all work performed.
• Artwork entire installation process in accordance with accepted technology.
• Using the too expensive, but necessary in the process of building tools.

In the case of the independent exercise of work do not neglect practical advice professionals.This experience will help avoid costly rework later coating.

Professional Advice

in any residential area is recommended to use self-leveling mixture only on the basis of polymeric resins.In areas where humidity is always present, you must use the self-leveling epoxy flooring views, while the rest of the house polyurethane floor.

Produce fill technology is provided on the concrete base, but is allowed and the installation of a wooden surface.At the same time the volume of work is increasing, as is required to produce high-quality training base with a two-layer primer.On this depends the strength of adhesion to the base wood coatings.