Production of doors with their hands in a bath

you decide to build a sauna yourself, which means you have to do and the door to the bath with his hands.

How to make a door to the bath?This will be discussed in this article.

door - an important part of the bath complex, it affects heat retention and comfort.Therefore, if you plan to make it their own hands, be sure to note the following points.

Always opening outwards.

The smaller the size, the more heat is retained inside the bath.Do not make the doors that exceed standard dimensions.

ensure air circulation, keeping the heat will help the threshold, 2-3 mm in height.

What are the doors?

Wooden - traditional version in the Russian bath.It is made of wood of trees following species: oak, aspen, birch.Input can be made of pine.

Glass - most often it can be seen in the Turkish baths.Behind the glass door easy to care for, it is good to clean, resistant to thermal stress.These doors are installed in washing and steam rooms.Metal

- sturdy door severe but due to high heat, and if it is used, only in an outdoor.

Door Thermoplastic - a modern kind of doors that are resistant to changes in temperature, strong, reliable, durable.

Often they replace wood as well as plastic allows you to simulate a variety of materials, including wood.

If there is sufficient choice of material for the bath is the most popular wood.

Photo:

independent production of wooden doors

to himself the right to manufacture and install the door, we need:

• boardof which we will be doing the web.Generally tongued, 30h200 millimeters;
• rails 30x20 and 30x30 millimeters, Strapping, reinforcement.For door frame beams 11h6 need millimeters;
• loops overhang;
• clamp;
• screws;
• glue;
• construction foam;
• anchor;
• sham strips.

also need a variety of tools:

1. screwdriver;
2. jigsaw;
3. plane;
4. hammer;
5. roulette and others.

input will be warmed, so the need for it:

• insulation;
• leatherette;
• cloves;
• Castle.

Step by step assembly instructions with their hands

Getting manufacturing door design with their own hands.

Standard Size - 2000h800 millimeters.Note includes height and horizontal length of the harness, which is made from timber.

Its width of 30 millimeters (do not forget that the rail is installed on all four sides).Thus, the length of the boards is 1940 mm.

is cut them to length.

calculate the required number of boards.

we remember about strapping 30 mm around the perimeter, with the help of mathematical calculations are not clever 800 millimeters (web width) minus 60 millimeters (two strapping) - get 740 millimeters.

Standard decking width 200 mm, we need as many as three and a board width of 140 millimeters, we obtain it by means of trimming the length of jigsaw.

composing all the elements of their own hands.To do this, you will need glue (best to use PVA) and clamp.

Handle recesses for workpieces with glue, fabric next door assemble, fastening clamps at the corners of the door leaf and leave to dry.

Most used workbench, which create the effect of the press.

Then gently treat the wood a plane to the web surface became smooth.

proceed to the trim.Is cut lumber to length 2000 mm and 740 mm, each with two.Fasten the details on the screws.

To fasten the harness on the corners, it is possible to impose their lap.

proceed to mount transverse slats to give the structure rigidity.Because the front door is to be insulated, we fix them outside only and are paving the insulation between them.

As a heater can be used mineral or glass wool, fine izoslon.Sometimes add a layer of batting.

Top leatherette cover, and nailed shirokoshlyapnymi carnations.At the edges to make the best rollers - they will close the gap.

remains a bit to make the door with their hands, namely, to establish the handle and hinges.

For bathhouse is desirable not to use iron handle because of their heating.It is better to install a wooden handle.

process remains transparent door leaf impregnation, which prevents decay.Note composition.Impregnation should not when heated give off toxic substances.

Installation

Form the box, using beams 11h6 centimeters.Be sure that the rack is always wider than the door leaf.The tool bar is necessary to make the groove on the outside, the door will go into it.

Leave a few millimeters between the frame and the canvas, as the wooden structure will expand from moisture.

Fasten the box using long anchors to the doorway, sealing gaps between the wall mounting foam, close frames.

proceed to hanging doors.Curtains have in the following order: one above, one below and one in reverse.

design is ready.In conclusion, we offer you to watch video instructions for the manufacture and assembly of the door with his own hands.

Video: