Bunk bed for a child with his hands

main thing - just to put

task is to determine what you want, if a quality product, it is necessary to understand that for the quality you have to pay.The cheapness of the evidence of the presence bolshihizyanov.
Making your own hands must include the fact that the article passes, and adult and child.Since its stability key requirement in the manufacture.
Some builders even made the bed with three tiers, which in itself is nonsense, which may carry unpleasant consequences in the form of children's falls.

What you need to consider when designing?

1. place the bed arrangement.
2. Where and how will be placed staircase to the second tier.

following note to the scheme, which marked the constituent elements of the bed of their size and location principle.

The only important point in the installation - this is what you need, so that the size of the bed was 8 cm longer than the bed, and the width - 10 cm more.

to the size of the staircase, you must add another 4.5 cm. To a bunk bed for a child with their hands properly functioning, it is necessary to take into account the height of the ceiling, after which mark the functional direction of the second tier.As is known, the second layer has several times higher temperature than another area of ​​the room.At this point, children can arrange recreation area, but it is provided that the tier will not be very high.

distance between the frame of the first and second tier bunk beds child with their hands should be such that if the first tier sat an adult, he will not beat his head against the frame of the second floor.

immediately lower tier successfully be done with special cabinets to store baby clothes.Calculate the size of the tiers is based on the height of the ceiling 2, 5 m, the thickness of the mattress is 20 cm, the size of the mattress -. 1.8 meters at 80 cm

Materials for

recommended to use ecological materials for the creation of children's beds.for example, it can be pine or oak.But there is no certainty that you will be able to find the size of the board 18h140 mm, 40x80 mm, 40h140 mm.And the parts that need to perform, too, can not be performed correctly and accurately.In this case, we need a hand specialist, because the work the tree requires special skills and knowledge of texture and properties of a particular tree.

Therefore, if we replace the tree on the DSP, so all the necessary processes for wood edging, frames, etc.It will be much easier and faster.You will need only pokleit machined edges on saw cut chipboard.

Although it will be inferior durability of wooden products.

Base articles must be created from 2 sheets of plywood 90 cm to 1.8 m to 9 mm, the constituent parts - 3 tubes of steel and PVC coating, fasteners - screws 3.5 to 40 mm, cap and glue.

Before the board used, they must leave the room at the time about a week to become the same temperature of the room where the product will be.This will save you from having to board does not warp.

Wooden parts require machining, special sanding, painting and others.This requires good equipment and tools: a drill, a saw, hacksaw, level, tape measure, milling device for smoothing uneven surfaces, or magnet wire detector.

interesting fact that the children's bunk bed with his hands from the material chipboard, has a weight of 2-3 times more than the product of the tree.Even chipboard bed cheaper 4 - 8 times.

process of making the bunk bed

1. Metering mattress.It should be added to each side of 2-3 cm for convenience tucked sheets.
2. 5-10 cm sizes Bars are attached with screws, that allows you to create two frames.

1. By the end of the frame need to strengthen the board size of 1.5 m to 2 cm. Fasten securely cuts itself.In the second frame must mount board (rim) has a 2 meter by 2 mm.
2. Manufacturing legs.Often the size of the feet is 25 mm per 10 cm. That was end of Form L needs to be fixed with screws, then putty length of the legs must be equal to the height of the fence, which is located on the second floor.

1. You will need an assistant!Fastening the flanges, drilling recesses of screws require additional hands.
2. certain profile placements.Note the location for drilling.Frame must be pressed, and to align the level of the wall drill.Must be screwed 6-sided screws, so take care of the good thin drill.Also, secure the bottom frame.
3. Bunk bed for a child with their hands require fencing for the safety of your children.Mounted on vertical racks of 5 to 10 cm. Screws are threaded on the inside, as well as leave room for the stairs.

1. lestnitsosuschestvlyaetsya installation by attaching two boards, which act and exit guides.Long bolts securing the upper rungs and ladder to the bed.
2. Installing plywood sheets.They are attached with screws and bolts along the entire frame.Because of this, it can be easily dismantled and set again somewhere else.
3. that the coating did not give highlights and look naturally, it should be painted matt varnish, which will make the look even more beautiful.

Follow the steps below, and the result will not make you wait a long time!