Make a fence of corrugated board in the home

Making fence of corrugated board with his own hands - the procuring

After evaluating all the advantages of a steel sheet as a barrier to your site from the street, you have set ourselves the aim of building a fence of corrugated board with his own hands, because the simplicity of this operation is one of the main advantages of this materiallater we see this.First, to measure the perimeter of your future fence and go to the store or market for everything you need.

minimum set of construction materials to make fences for the cottages made of corrugated board with his own hands, depends on your project.You can attach sheets to the joists of the shaped tube, using as a basis metal poles, buried deep in the ground.This will be the easiest and least costly option.If you want columns of brick, foundation or some other complex structures, the time and money spent will have a lot more.

So buy steel poles , shaped tube 40h25 mm metal sheets about 2 m in height. To determine the number of all of this, take the fence length, which we recently counted and divide it by 3 (for the number of columns)and multiply by 2 (for the number of profile pipes).The math is simple: the pillars are placed at a distance of about two and a half or three meters from each other, and shaped pipes for attaching the metal sheets need at least two.Adjust these numbers it is already possible to your preference, this is the standard version.

number of sheets of corrugated board depends on their width.Remember!It is best to fix them vertically.

How to make a set of corrugated board with their own hands - preparing the work site

now can be discussed and the process of how to build a fence of corrugated their own hands, video and detailed instructions will not let you make mistakes.It begins any work with the preparation.To do this, the entire perimeter of the site is cleared, land leveled , if there are any bumps, wormholes and other inconveniences.

next step - pit under the pillars.They can be, of course, simply to drive into the ground at a depth of 1-1.2 m, but it is not so easy.So if being constructed of corrugated fences with his own hands, it is advisable to dig a small hole and concreted poles there.Do they need to be in the form of a cone, one end of the hole must be larger in diameter than the other, it will provide stability.Poles put in the resulting space is filled with rubble and the concrete is poured.It is desirable that they were placed precisely and also froze to your fence does not look rickety.

Further, as concrete has dried up, continue to manufacture corrugated fence with his hands, and on the turn go lags , for which we charge a small shaped tubes and welded to the posts in two rows (number of rows at your discretion).The first line should be a lag of 25 cm from the ground, the second - the same distance from the upper edge of the fence.Calculate this can be the length of the sheet and its projection on the pole, because the receiver you mount on him, but that does not is the highest point of the fence (although again, this time quite subjective, consider, on the basis of your project).

Mounting fence of corrugated board with his own hands: how to act properly?

Now we have almost grasped the skill how to make the fence of corrugated board with their own hands.After all, the foundation is ready, it remains to fix steel sheets.This is done roofing screws, they are driven into the material easily, hold tight.Perhaps somewhere sheets have to be cut, unless they enter the width in perimeter fence integer.Location of the depressions should be corrugated sheet, at a distance of at least 50 cm, although it depends on the sheet width and thickness.

between them should be left so much space that there is no freewheel sheeting between the two attachment points, such as the sail will play a bad joke during strong winds.

That installation of the fence of corrugated board with your hands is almost complete.It is necessary to make the gate and gate, for it will come down again quite profiled tube, from which you can cook the desired shape, and a sheet of corrugated board.Hang it all in the loop.Now the fence is ready.But to delay the welding machine is far too early.Poles are not obstructed from the top to prevent water from the base of the winepress in the rain, weld visors.Now exactly all the hard work is over, paint poles and logs paint, and enjoy the result.