Booths for dogs with their own hands .The drawings and sizes.Top Workshops

Dimensions booth for dogs

Dimensions booth for dogs can be adjusted depending on the actual dimensions of the dog.So, his chest should move freely in the hole structures.Therefore, its width must be added from 5 to 8 cm. In this case, the best height of the manhole is a value which is less than 5 cm of dog at the withers.At the same time, the maximum vertical size of the booth, and its depth should be 5-8 cm longer than the height at the withers of the animal.

booth sizes for dogs.Photo

booth sizes may vary, but in a big way.Especially important to follow this rule when the design is created for the puppy.In the construction of the booth for the dog with his own hands must always keep in mind the following points:

• Dog in her housing, nothing should get in the way so that he could freely go or be.
• Inlet has to be comfortable.For this purpose it can even increase slightly in size.
• structure necessary for the dog to warm , to the dog in the winter was warm.
• roof and wall structures must reliably protect different animal from rain and wind.
• booth must be built from environmentally friendly material.It is best if it is created from wood, since wood is harmless to the dog's health.
• construction should be placed on the territory of the infield with the windless side.This dog should have a maximum review.
• A good option is the construction of the booth, which is provided in the roof of a small attic , where you can store different things, including toys and dog bowl.
• Laz recommended on a short wall.Thanks to this arrangement, the dog will be easier to climb in your home.
• Before creating facilities for the dog must be careful to make payment size booth.It is best to double-check the size several times.This will build the perfect design for the animal.

booth for the dog with his own hands - drawing

booth for the dog with his own hands.Video instruction

Doghouse with gable roof.Master class

roofs with two slopes is recommended to create booths with small size, because such designs increase weight structures that are awkward to lift during harvest.

booth drawing for

dog Step 1: Create the frame

bottom frame made of four bars, each side of which is 50 mm.Its corners are fixed stand upright.Their size should match the height of the booth.In the upper part they are strapped by the same bars.The strength of the carcass booth for dogs is enhanced by securing additional jumpers on the bottom and on both sides of the manhole.

how to make a booth for dogs.Step by step photos

Step 2. Mount the roof

Made two designs, each of which uses two bar 50x50 mm.They are connected with each other so that they form an angle of 40 degrees between them.Billets are mounted vertically on the frame flush with the lower walls and temporarily fixed with nails.Two blanks mounted in the upper points are interconnected by a horizontal bar with the same cross section.Thus it is necessary to provide that he is in front of the kennel performed at 200 mm.Further, the two bars of the same length are fixed at the lowest points of the rafters.

Step 3. Boarding kennel

Wooden Kennel is sheathed on the outside lining.During operation, you need to make sure that there were no gaps between the boards.Roofing felt on the bottom plank and fixed supports made of beams, if necessary.

Step 4. Warming

first booth cage for the dog on the inside is lined with glassine paper.It is fixed at the corners by means of staples.Then, fixed foam or mineral wool.Then the heater was covered with glassine paper, plywood on top of which is attached.It also is laid on the floor.

Step 5. Roof Sheathing

temporarily fixed roof frame is removed, and its interior is sheathed with plywood.Then the design is turned into its natural position.Further, on the plywood fastened asphalt, which is laid insulation.Then, heat-insulating material is covered again Pergamino.At the end of the fixed profiled.For its fixing screws are used.

booths Shepherd with his hands.Step by step photos

If the booth to make their own hands with an opening roof, which is a bias in one direction, then this design will facilitate the process of cleaning and disinfection of the house for a dog.It still allows the dog to stay on top of their homes, as many dogs love to be in such places.

is important when creating a kennel perform insulation.This will protect your dog from the cold.Also, this arrangement contributes to the manhole in the wall of a larger size, but it should be pushed to one side.If a rule is carried out during the construction of the house for a dog, the animal will be a great warm place.Thus it will be protected from the wind.

Step 1: Create the frame for

bottom in the drawing booth for the dog come from bars, each side of which is 40 mm.They cut off the size of the bottom.Then they form the box on a flat surface.Its corners are fixed with screws.If the dog is large, the frame needs to be strengthened.For this purpose there are fixed the additional web.She then, on the one hand, sheathed boards.

booth for Shepherd with his hands.Photo-step

Step 2. Warming bottom

frame, coated on one side, boards, bars flipped up.Its inner part veiled glassine, which is fixed with staples in the stapler.Then, a styling foam between the bars.This material is cut according to the dimensions of the frame, and its thickness should be equal to the height of the boards.Then insulation hiding glassine layer and create the finishing floor.

Step 3. Making the frame

Referring to the drawing booth for dogs timber with the size of each side of 100 mm is cut into 4 pieces.Two of them have a length equal to the height of buildings and other 2nd frame members have to be longer by 70-100 mm.All pre-cut bars are mounted in the corners of the bottom vertically.Racks with longer front fixed by means of nails or screws, and other - in the back of the kennel.Thanks to this arrangement, the roof will be sloped.It is also used to create additional frame bars which are fixed on the center wall in a vertical position.On each side of the manhole is also installed two bars, but they are small.To carcass improved strength necessary to use metal plates, whereby the internal reinforced joints.

Step 4. Installation plating

wall linings used for the outer skin structure.Then warmed booth inside the frame for the dog.First fixed glassine using steplernyh staples.Then fit the foam or mineral wool between the bars.Next, insulate the material covered glassine, which is closed with plywood.Also it is possible to use any other particle board or similar material.To fix the cladding is necessary to use small nails with a zinc coating.However, their caps should always be recessed into a tree, so that the dog could not hurt.

Booth for Shepherd.Photography workshop

Step 5: Create the roof

pent roof type is made by using bars, in which the size of each side is 40 mm, and a sheet of OSB .First, the frame is created.Its dimensions correspond to the inside length and width of the booth.Then, from a sheet of OSB cut piece of the same size, which is attached to the manufactured structure.Then, in the frame fit insulation.It must cover the film.For fixing it using the same stapler.The next step is cut out another piece of plywood, the size of which shall be on three sides by 100 mm longer frame house for the dog, and one (front) - 150-200 mm.This will protect the walls of the hole design and different rainfall.

If the hand is not a sheet of plywood or OSB, you can use the boards, whose thickness should be about 25 mm.Create a design, padded tiles or roofing material, fixed to the kennel with the help of loops.

Step 6. Perform finishing

Ready booth for the dog from the outside is treated with antiseptic .Also suitable for this impregnation.Deposited funds must dry completely.Then, at the bottom of the structure is fixed roofing material.This insulating material has to go 50 mm to the walls of the kennel.Further, on the roofing material is secured two bars whose size is 100x50 mm.They must also be treated or impregnated with an antiseptic.Then the house is flipped and the design of it is done with the help of wooden manhole casings.

Step 7. Installing booths Shepherd

After completing fabrication booths chosen place for construction.It should always be closed from the wind, smooth, dry and close to home.Best of all, if the place is well-lit and located far away from any overhang or tree.The latter feature allows the dog booth installation, if necessary, to hide from the sun's rays.

Ready booth for Shepherd with his hands.Photo

booth with a vestibule with his hands

booth for the dog to be more comfortable, you can build it from the vestibule.Such a home for dogs is composed of two parts:

• distal portion, which is sleeping;
• proximal portion designed to increase protection from the cold and drafts.

Branch divide among themselves by means of insulated walls, which houses a manhole.

Make a booth for dogs is not so difficult, but its construction is not recommended to do a great sleeper, as virtually all dogs curl up while sleeping.It should be possible to stretch the animal freely on the platform when it is in this place to rest.Therefore, the size of this part of the house should be appropriately acce dog.

Booths for dogs with a vestibule.Dimensions and drawing

assembly design with tambour is exactly the same as the other booths.A distinctive feature of this house is partition between the two branches of the dog house.It is created from bars with a cross section 40x40 mm, plywood, insulation material and screws.First, the frame is made, the dimensions of which correspond to the width and height of the booth space.Then to it, on the one hand, plywood nailed.Then it is placed insulation, which is fixed on top of another sheet of plywood.

To septum could easily remove the need to take two wooden slats and selecting them in the longitudinal grooves via milling.Their width should be equal to the thickness of the septum.Thereafter rack fixed to the walls of the booth.After that is inserted in the septum by the slots.

Kennel of the timber (for Alabai) with his hands

Following the calculation of the booth size to get the next drawing, which sets out indicative size of the home for a large dog, for example, Alabai.In addition to the manhole, the structure can be provided in window for review.It must be positioned in the side wall.

Booth for Alabai - drawing with dimensions

Before the construction of the kennel of timber is best to perform the construction of the platform of logs.They need to be planed and put together into a single structure, which then need to be painted.After that begins the construction directly by the kennel.The construction process will be carried out quickly if the boards prepare in advance.They need to be cut off by the size and planed on all sides.

According to the developed drawing the first home the crown for the dog put a whole.Further, the side walls are made also from whole logs.Where there is a manhole and window pieces of material used.

After the erection of structures carrying booth construction is carried out of the roof.It is best to make a "house", to her not accumulate a lot of snow, so as a large area of ​​pent design will contribute to this.In the home for a large dog is necessary to provide ceiling.He will make the kennel warmer.Since its establishment the build of the roof panels.This truss system is not made, if the design fulfills a decorative role.On the boards laid by roofing material.It can be soft or metal tiles.It is best to use the material, which was used in the construction of a residential house or a bath.After that, the shields are connected together with nails or screws and wrong gable design.

At the final stage made the roof is fixed on the walls of the kennel.Thus insulate frame booth is not necessary for the dog, since it is made of timber.The material itself is warm and has a low thermal conductivity.

Care doghouse

Now that it is known how to make a booth with their hands, left to find out how you need to take care of it.First of all, you need to remember that cleaning is a home dog should be done regularly.Usually it is performed once a month.This disinfection designs held in the summer of each month, and in winter and spring - once a season.

While cleaning the kennel removed the bones and other leftovers, carried home treatment Lysol , allowing to get rid of parasites.Also for these purposes may be used, or three percent creolin formalin.It is forbidden to let the dog in the booth until the solution has dried!