August 12, 2017 18:07
Gateway running on automatic drive, conquer many practical uses.Activate them by simply pressing one button.There are the following varieties:
The design of this type is the separate sections connected by hinges, moving on rails set out in the opening area.It is common today to view the mechanical gate.Movement of the web takes place vertically in daily operation is convenient.And all because for such automatic gates do not need the space and before entering the car can be placed directly in front of goal.
in the garage for more convenience, you can complement the sectional door wicket or put a side door.In addition to the convenience of additional construction will minimize all the possible heat loss, as well as increase the level of safety of the facility.In addition, you can restrict access to the garage, picking up the latch in advance, the ability to open a flap from the inside.Outside mounted bolt lock cars, equipped with flip the puck.
Automation gate on the sections characteristic ease of installation and a high level of convenience in the further use.Managing such a structure is possible by means of the electric drive, operating on the remote.When you turn off the electricity gate system automatically adjusts to manual control.
sliding gate when installing facilities recoil species it is necessary to consider the following points:
This design is popular due to affordable cost, system reliability, and design security.Everything else they are functional and have an unlimited range of architectural solutions.Enough demand today forged models equipped with an automatic system.
Hinged gate type composed of these elements:
When choosing a particular type of swing gate should take note that not every model has a mounting drive.These restrictions are associated with the weight and dimensions of structures shutters wide.Be sure to note where the drive can be positioned, because it can be attached to the load-bearing columns facilities, racks, or flaps, as well as the outside of the system.
are going to mount the gate with a sliding mechanism, you need to be patient and follow the guidance described below.Compliance with all rules will help you in this difficult matter.First you need to call the three steps that need to follow:
concrete foundation is laid on the border opening, that is, on the side of the gate rollback.This foundation must be equal to half the length of the journey, and the width - not less than two feet.Through the foundation size calculations should not forget about how the ground freezes in winter (up to 2 meters).
Making the frame structure of the metal foundation, at the same time use the fitting "AE12" and channel "18".Through weld combine these elements.Thanks to u-concrete base becomes stronger and more reliable.The length of the valve forward so that the rods are gone into the land exactly on the freezing line.Durability frame received through connecting horizontal elements with vertical webs in the design.Now you are ready to install the carcass in a recess in the ground prepared in advance.Before that, a good layer of compacted sand.
Before filling the base with level check the levelness of the power frame.At the bottom you can immediately lay pipes for wiring under the automatic mechanism.For pouring the foundation used concrete solution from the gravel, cement and sand.On the foundation of freezing will take about 120 hours, after which you get a robust design.
first determine, according to a trajectory of the gate will move.To do this, pull the cord off the ground at the level of two meters.This makes it possible to align the beam that serves as a support.Putting roller mechanisms, and then install them in the support beam.Then set the channel on the thrust fold doors with already built-supporting mechanism, as outlined in the points put the two pillars.Then fasten to u roller mechanisms.After that, we take such action:
Then begin setting motion gate, which you need to loosen the wrench on the connection supports.Try out mechanism - the support rollers should take the right position.Tighten all bolted connections.
Putting further plugs and trailer clip.Insert it into the tube-shaped outer side with n structure, and then all the anchoring bolts.The plug fastened by a weld.We carry the top of the guide bracket assembly using bolt breaks, which are connected to the rollers.We carry out the adjustment accuracy of the tilt, spin bolts.
At the last stage of the work collecting the lower trap.Laxative bolts and close the gate.After the combine separator with a gate, thus we make sure to touch the corners of the upper trap.Spun bolts.
Regarding the installation of the automatic system, it is mounted on the rack, which will move the structure.Securing the rails occurs at the user's profile, which is supported.Then mount switches, electro-mechanical components, signal lamps and other items.In order to simplify the work, you can watch the video.