Plaster walls on beacons - training and work

value and features walls on beacons

plaster Besides simply decorative functions, plastering of the outer walls improving their thermal performance, the surface get extra protection from inclement weather and increased fire resistance.In addition to purely utilitarian purposes, the important role played by the attractive appearance.For a flat wall is better, if carried out on plaster beacons.This smooth surface accumulates less dirt and moisture, and is self-cleaning, etc.

applied layer is kept longer on the ground, is less susceptible to the destructive influence of precipitation and temperature changes.Depending on the reasons for applying plaster on plaster beacons technology allows you to use special crates in the form of thin strips of wood to three centimeters wide, stuffed in the wooden walls or ceilings.Rods are sometimes referred to as shingles and attach diamonds, bars, with the side to six centimeters.

This lattice can be replaced by metal or plastic reinforcing mesh.These methods are justified when the surface level difference plastered wall from ten mm.High plaster walls under beacon is performed based on the minimum thickness of the layer and its thickness, in turn, should not be less than a centimeter by 0.5 centimeter tile or wallpaper under the thinnest point.

course, you can align the wall with the help of plasterboard systems, but the loss of the area and height of the ceiling is not justified in any room.Furthermore, it can be done easily enough plaster beacons on their hands, which reduces the cost of the work, given the opportunity to apply ready-made plaster system with selected compositions of layers and their desired characteristics.But as well the use of compounds prepared according to the recommended recipes yourself.

finished walls and

tool With a little experience of work installing beacons for plaster would be a perfect way to get the guaranteed level surface.Before starting the work necessary to prepare some tools.Traditionally, the blade will need plastering, fit and construction trowel for spraying a large area is convenient to use a bucket.

also need: Falcon (rigid plate 0,4h0,4 m below the handle) to set the working portion of the solution, float (with the working surface, padded cell) and poluterok (up to a meter in length), wide brush or a brush, sponge, plummet, usually with a sharp edge (preferably metal to the height of the room), cable nylon, building level by 2 meters.

will be needed screws, dowels length of 4 cm or more (depending on how high the installation of beacons will be held under the plaster)electric drill with the function of the gun, a hammer, a screwdriver under the form of slot bolts, marker or pencil.Before starting work, the wall must be prepared.This training includes its thorough cleaning, dust removal.Then the wall marking is carried out to determine the mounting locations for lighthouses under the plaster.

Partitioning wall plaster beacons

Such works consist in marking the walls, starting with the application of a vertical line at a distance of 0.4 m from the corner (wall edge), checked the level or plumb.From the ceiling and floor distance and not more than 0,4 m. The upper and lower point, and the middle of the resulting line will allow to correctly identify the right places before install beacons plaster.

Through them and the middle of the first vertical take place horizontal lines, also verifies the level and plumb.At a distance of not more than 80% of the length of the metal rule with a sharp edge you need to hold another vertical line, guided technique for the first vertical.

With great length of the wall is evenly divided into segments, the distance between them should be indicated.This requirement is due to the need to align the existing layer rule.

After drawing vertical lines from the corners of the rectangle can be obtained to hold the diagonal.When correctly performed markup they intersect at a point on the median vertical, which is both a line of symmetry.Thus, at the intersection of verticals and horizontals are places of location beacons.In the Internet enough movies where in the video mode, the installation of beacons plaster is shown in detail, even with pre-marking.

In fact, it is a fairly simple operation, although it requires careful execution.An important consideration in the conduct of training is and how to put beacons plaster adjustment.At this point, it provided no depressions and mounds on the future of the layer of plaster.Here you will need a cable said.It stretches between the dowels with screws screwed in recent cue point.The entire length of it should not touch the wall.

When you are ready to spray Lighthouse pyramids of working solution.A handful of the solution is pressed at the top of the pyramid-rule strip all the way into the screw lighthouse.It may then be conducted on the plaster walls beacons and video after the article shows how the sharp edge of the rules easier to remove excess solution.

Note that obryzgovy first layer should be about 5 mm.Then comes the main application of the base coat.The number of layers depends on the required thickness across the plaster, but it is not recommended to put more than ten mm at a time.Dirt layer can be covered with a finishing layer and smooth down trowel or overwritten, depending on the need for further work.