A fence of corrugated board to strip foundation - strength and impregnability

fence of corrugated board to strip foundation - it's expensive, but reliably

Country house usually means that there is some, albeit small, of land, which must be enclosed with both the neighbors and from the street.It is desirable that the barrier was impervious to the views as you like, and those who live near you, have a right to privacy, without opinions on it from others.The first thought that occurs in many - brick wall height in two human growth.But it is not nothing but a waste, since it is possible to achieve the reliability of the fence without such radical means, you just install a fence of corrugated board to strip foundations.By the way, this type of foundation is divided into two types: monolithic and modular, which means you have a choice.

When the priority of speed and price does not matter, you can use the services of contractors and installed using a crane concrete blocks, received as a result of assembly strip foundation.These building blocks are produced at the factory and service life obtained with their help, the base of the fence is rarely more than 65 years.The bulk of the work falls on the digging of trenches for immersion in her block.Next, set poles, belts fastened reinforcement obkladyvayutsya blocks and poured concrete.A cheaper, but requires much more time - reinforced strip foundation.It can be obtained by pouring the cement-sand mortar of gravel, rubble brick rubble (the whole mixture flavored with reinforcement).However, the foundation technology for the manufacture of fencing requires a more detailed description.

Foundations under the fence of corrugated board to guarantee a half century

If the site already was being built, so the basic data about the soil you already have, otherwise they need to get: the depth of groundwater and soil structure.Then, making sure that everything is in order, and at this point you can install design with a high sail, begins counting at the trench for the foundation.The next step - directly earthworks, delve into the ground 40 cm, width of the trench at least 20 centimeters, where you provide the pillars in the trench dug the pit to a depth of more than 40 centimeters. distance between the pillars of the fence of corrugated board - about 2-2.5 meters .Next - Installation of supports, which are lowered into the pit prepared for them (in the pre-recess can omit the rolled roofing material), and hammered into the ground more centimeters by 20. It only remains to tie the pillars of reinforcement zones, approximately 10-15 centimeters below the edge of the trenchYou can start up around the foundation reinforcement cage to increase the strength of the base, the bar thickness can range from 5 to 10 millimeters.

Now, depending on what type of foundation is selected, stacked in a trench one-piece, or it is a little more than half filled with gravel mixed with crushed brick and broken cobblestones.Filling watered and compacted.By the previously prepared reinforcing belts horizontally welded on the two valves so that they are 5 cm did not reach the walls of the pit and its content.Then comes the final stage of preparation for pouring the foundation - set timbering.It is best to use prefabricated metal, it is easier to operate and take it not as an example better.Height of plinth foundation may be different, depending on your desire, but possibly at least 20 centimeters.Accordingly, the height of the formwork must be the same, or even better 5 centimeters above the planned height of the plinth. Pouring cement-sand mixture is carried out in layers, in order to avoid voids.When the formwork is filled, we keep our structure to gain strength for 2 weeks, with water pouring cement surface on hot days.

foundation is ready, remove the casing and install decking

It is not necessary to wait for complete hardening of the foundation, it is enough that the cement has hardened slightly to remove the formwork.In its place, the cement between the band and the earthen walls of poured sand, grit it does not matter.The supporting structure for the corrugated board is going on crutches at the time when the cement attains maximum strength.Logically, the on-site installation of the gate with a wicket base foundation is to be interrupted, but the underground part is quite right to exist.The framework for the corrugated board is manufactured by welding of profile pipes section 40h20 mm, after which the same method or by bolting mounted on the support.Holes for mounting corrugated board made simultaneously in the metal rolling and bridges so that they coincide.

determine in advance, you will use the self-tapping screws or rivets for corrugated board, but it is better to select the past, this option will eliminate the possibility of dismantling the fence site without your knowledge.

number of fastening points sheeting, regardless of whether it is self-tapping screws, bolts or rivets must be adequate to each individual section of the fence can withstand gusts of strong wind even.By the way, for the rivets need a special tool, the screws will require only a Phillips screwdriver.because profnastla sheets mounted vertically in the enclosure, they need to strengthen the overlap on the same wavelength.It is recommended to strengthen the fabric of the fence adjacent to the foundation plinth, without a gap, in order to fully protect your site from prying eyes.Top barriers to smooth lines can be installed fence pickets, but it is up to you (and you can pull the barbed wire).