Cdvizhnye the gate with their hands - step by step instructions

In our country sliding gates gained a lot of popularity in the Soviet times, when this opening system installed on most businesses.Now the gates are installed in backyards and fences cottage settlements.Great popularity sliding gates have received thanks to the ergonomic design, which saves space.

Make a sliding gate for your site and everyone can.This will require you some time-consuming, but the gates made their own cost less than ordered by a specialized company.

To understand the structure of sliding gates, explore their drawing enough.In such a system there is no complex or clever elements.Everything is simple and reliable.

sliding gates set into a welded frame to which the web leaves the gate open.The frame mounted roller bearings closed type, which facilitates opening and closing the gate.At the same time the carriage rollers from inside the frame, protected from rain and external impact, thereby reducing maintenance to a minimum (bearing lubrication only when the gate) and extend the life of an average of 12 years.

can be used any material -DSP, siding, metal siding for finishing the gates, one-piece steel plate or any other.

from your wishes and financial possibilities depending whether the gate shift manually or via automation systems.Also it is necessary to decide for what purpose it will be used gates: a main entrance, fire (evacuation) output or as a backup in case of problems the main gate.All this determines the size, appearance and cost of works on installation of the gate.

Gates mounting

1. Installation frame future gate

first step in the installation process is the installation of the future opening the gate.For this set poles made of two steel pipes, bricks or wooden beams.Poles should go into the ground at least a meter, it is at this depth the soil freezes in the winter.Poles are installed in a pit of depth, aligned and filled with cement mortar.

For complete drying the solution should be about a week.

2. The foundation for the gates themselves

To set the frame also requires the foundation.For its production we take the channel width of 20 mm and 15 mm diameter rebar.Reinforcement is cut into pieces and welded meter to u vertically.As a result, the design should get, like scaffolding.

Under the foundation dig a pit whose length is exactly half the width of the door opening.The width of the pit 40 cm, depth is not less than a meter.

placed in the pit structure of the valves and channels.It is necessary to note that the level of sill position relative to the ground level determines the width of the gap between the door leaf and expensive.After placing the foundation frame hole is filled with cement mortar and allowed to harden.

If you did everything right, you'll have a flat metal platform on which the guides for the gate to be subsequently installed.

3. Support frame

to manufacture door frame, we need the metal pipes with diameters from 30 mm to 60 mm.the pipe must be cleaned of rust using a grinder or sander, degreased and primed.

After tube processing is complete, proceed to weld the frame.In the frame of the finished pipe is attached crate of pipes of smaller diameter (eg, 20mm), which will become the basis for the skin.Sheathing is attached to the door leaf by means of screws or rivets.

Location crates inside the frame is determined by how you want to bind the gate.When unilateral sewings crate is on the edge of the frame, with a bilateral - in the center.

When carrying out welding work make welds in increments of 25 cm. Is the optimum distance for maximum structural strength.

After welding all the seams are compared grinder, and the door leaf is primed and re-painted.When the paint is dry, you can begin to sewings fabric chosen material.

4. Installation guides

Installation of doors themselves begins with fitting guide.Set the lower rollers, bearings and guides to the open position.Note the position of the first and last clips from them to the edge of the gating fabric should still be free space.

on rollers put the upper guide and the gate to align the rollers on the level.After that, place the rolls on the frame of the goal and re-set all on the level.If the frame is level, tack welded to the foundation platform rollers, weld the upper and lower traps.

upper rail fixed to the previously established posts, and the rollers are mounted on it.If the poles are made of metal, you will not have problems with welding.If brick or wooden pillars, use of anchors or embedded reinforcement.

5. Installation of gate wing

roller carriage is recommended to weld in easily accessible places, to avoid problems with the repair or replacement in the future.

lower rollers, as already mentioned, are welded with their platforms directly to the foundation, while the upper rollers are mounted on the rail with screws or welding.Option with bolts allows you to replace the rollers if necessary, weld the connections have to be cut and re-digest.

6. Installation of the upper rollers on the lateral rolling

Instead of directing the beam from the top, you can make several vertical guide rollers.They are mounted on a U-shaped profile with bolts.These videos will not allow the door leaf to swing and play the role of a guide beam.The advantage of such a system is that a door opening is not created for the passage of high obstacles vehicles.

7. Installation of the lower trap

At the lower edge of the foundation should be welded to the lower trap, which will go door leaf.This creates an additional point of support, which allows release of the load rollers.

Experience has shown that the production of sliding gates in the home would greatly save finances.Making the gate in the company would have cost twice as much.Moreover, the construction details and elements are not a scarce commodity.With the proper observance of technology of installation of your self-made gate will last you much longer proprietary.

Video - Installation of sliding gate