Search methods for water wells in the area

How to find water wells in the area - an issue of concern to many people, because without it is impossible to establish any farm or live comfortably.

incorrectly selected area under the well can ruin the life of the whole family.First, the water is not enough for irrigation.Secondly, it will lack for household needs.

There are cases when drilling in the wrong place causes produce poor-quality water with a lot of impurities, which is not safe to drink, so it is important to find the right place for the well.

However, living in a private house, you can not be afraid of the arrangement of the well, if you know how to look for a source of water and to act according to clear rules.

There are many ways to find water to wells.It is quite possible to do, even on their own, without the involvement of professionals.

Designated water occurrence

water almost impossible to find on the surface of the ground.It accumulates in this case is only in the valleys - man-made or natural.

most often in the area the water is in the ground: on the first clay layer or below, so finding it is not so easy.Sometimes the depth at which seek mine, comes to fifty meters or more.

Moreover, we should not think that you can simply drill a hole, going too deep in the ground.

Yes, indeed, it is very easy to do well at a depth of several meters, but in one voice experts say that it will create only extra headache.

So-called perched does not meet the sanitary standards, may contain impurities of sand and clay, dirt.

wells at this depth dig more often in the cottages, which needs constant watering, and water quality is not important.

Finding veins are occurring on the lightened method, especially if there is a body of water.

Then dig a well near it, delving below the water level in the river.However, there is a high probability that a well with technical water due to shallow location quickly dry up.

The area is best to do well at a depth of ten meters.This is where you can find filtered water and suitable to meet the requirements.

deposits can be both for pressure and free-flow.In the latter case it is necessary also to connect the pump to pump water.

Of course, due to the drilling of certain expenditure.The most expensive would be to find a vein of mineral water, which lies at a level below thirty meters.

It is full of useful elements and materials, but this drilling will cost a decent amount.

Where do well?

If all is clear at a depth it is necessary to determine exactly where on the site to do well.

It is understood that the well should not only meet the requirements of the owners, but also to certain sanitary standards.

Video:

Drilling is prohibited in the following places:

• place in the hole located on the distance of five meters or less from the foundation of the house (ie, cleaning the well, or can destroy a house);
• well will be located closer than thirty meters from the septic tank;
• can not do well, if it is located at a distance of five meters or less from the road;
• if under the well site is located nearer than thirty meters from the site's neighbors;
• well will be built at a distance of less than fifteen meters from the natural reservoir.

That is, in all other places it is possible to build a well, if this place was able to find the source.

And if the soil meets the requirements, the drilling does not matter whether the well will be, for example, in the rock or on the upper levels.

wells Search: test drilling

most reliable and proven way to search in the area of ​​water is considered a test drilling.Its actually do on their own, without hiring professionals.To carry out the work required a manual drill.

its diameter selected depending on the soil in which drilling is performed.If necessary to drill into the rock, you may need an automatic drill that can cope with the stone.

Test drilling makes it possible not only to determine at what level lies the water at the site, but also to determine its quality.

typically drilled to a depth of about ten meters, so it is important to take care of the possibility to build up a pen.

If it is not a rock, but an ordinary black soil or clay, then fit a drill with a screw with a diameter of about thirty centimeters.

Video:

to conduct test drilling, is necessary to slowly and gradually deepen the drill.Already after the second meter every fifteen centimeters tool you can pull out and check.

When the screw will be wet, immediately you can identify what it is at this level lies the water.

Alternative ways to find

search method using the test drilling of the well is not for everyone.

Firstly, there may not be a drill at hand.

Secondly, in certain areas, such action is hampered by the soil (for example, when it comes to rock, the drill holes will be permanently impossible).

There are ways that take very little time - they are elementary and simple in design.
example, water can be found by means of silica gel beads.

new balls are not suitable for the process.To bring them to the desired state, you need to dry them in the sun or in the oven.After that, a handful of balls placed in a clay pot.

further need to weigh the pot - this is an important point, which later will determine how much water is in a selected area.

Pot wrapped with a thick cloth and buried at about a couple of meters into the ground, where planning to do well.We leave it for a day.After - dig and weighed again.

If the pot is significantly heavier, hence, he absorbed enough moisture, and the place is chosen correctly.

This method is very effective, because the gel - a substance which actively absorbs moisture and keeps it.To search

not dragged on for several weeks, it is possible to bury several pots on the potential areas for wells.

You can also try to determine the water level with the aid of a barometer.But first it is necessary to set up, which made pressure measurements on the banks of the nearest pond.

Then you can measure the pressure at the selected well site.To understand how deep-seated water, it is necessary to look at the difference in values.

Thus, the rate of one millimeter of mercury corresponds to depth of twelve meters and 0.5 - six.

You can also search for a place in the well with the help of frames.For this most commonly used aluminum structures.For example, take two wire segment length of about thirty centimeters.

Bends of about ten centimeters, so that the construction forms a right angle.You can insert the ends into the elderberry sticks (no core), for convenience.

become, keeping both hands on the frame, elbows pressed against the body.Then slow steps go around the site without making sudden movements and trying not to affect the sticks.

is believed that the place of occurrence of the water, the frame must interbreed.If the ends are crossed and do not differ, even if you took a few steps, it means that you were able to find a real mine.