How to fix the creaking wooden floor

In many older homes still preserved wooden floors.Wood flooring has long been considered a sign of prosperity.Wood - a strong and durable material that will last for decades.Therefore, get rid of the wooden floors, many owners do not dare, because he is considered to be an environmentally friendly material and retains heat in the room.But there is a troublesome problem of the old wooden floor, a characteristic sound.

creaking wooden floors - a common phenomenon, and many wonder how to fix the creaking wooden floor.

will understand what are the causes and what to do when the creaking wooden floors:

According to professionals, the sound may occur due to friction:

• when the flooring behind the base;
• split one or more bars;
• board rassohlis;
• broke groove or ridge;
• become loose nails or screws;
• fasteners went outside;
• around the walls there is no gap;
• when the ends of the boards come into contact with logs.

Let's see what kind of floor structure is installed in your room:

1. floor structure consists of sheets of fiberboard, which are laid on a concrete base.On top of the concrete stack logs (wooden block) at a distance of about 40 centimeters from each other.The top layer is sewn up with plywood or particle board, and then laid a layer of fiberboard.
2. Common Design - directly on the concrete floor joists set, on top of which is attached a wooden board.

wooden board nailed to the joists with nails normal, which over time under load (walking, jogging, rearrangement of furniture) are loosened.Get rid of the characteristic squeak impossible.The only option that allows you to eliminate the creaking wooden floor - remove the old boards, and put in their place new ones.This work is considered to be complex and expensive, so let's get rid of the creaking of the known methods.

When to get to the bottom of the floor is not possible, then the board can be fastened with screws to the joists directly overhead.

methods of getting rid of the creaking

There are several methods of how to remove the creaking wooden floor:

• podbivanie wedges;
• fill the hole with foam;
• use anchors made of metal;
• laying plywood on top of the boards;
• tightening with screws;
• floor screed.

consider in more detail the methods of getting rid of the squeak.

Podbivanie wedges

main reason why creaking wooden floor - it's bad attached to logs or wooden beams of the board.When people walk on the floor, the board eventually lapped, and because of this there is a special friction creaking.To get rid of the friction in the space between the boards clog small wood chips or wedges.

If creaking reason - the friction of two or more boards to each other, while in the gap to drive a wedge at a certain distance, but not more than 15-20 centimeters, and so they were not on the same level with the floor.

To eliminate squeaking by podbivaniya wedges are needed materials and tools:

• hammer;
• metal rod;
• wooden wedges.

Using a hammer a wedge is driven into the crack.If necessary - to this place a thin layer of wood putty and leave to dry completely.

If your slot is very small and the possibility to insert the wood chips are no such space is filled with graphite powder or talc.

Filling the holes with foam

Despite the fact that this method is considered to be inefficient and costly, some newcomers to the construction business is still trying to eliminate squeaking in this way.

In order to fulfill the minimum repair boards, mounting foam fill the hole.Drying up, the foam expands and hardens.Thus it lends rigidity coating.

ineffectiveness of applying foam proved by the fact that the emerging foam load prominaetsya and crumbles, and that means an unpleasant creaking return again.

The use of metal anchors

When at the base of your wood floor is a slab of concrete, then to eliminate the squeak, you can use a metal anchor.They are fastened by hand.Actions are:

1. electric drill or hammer drilled small holes in the board and the concrete slab.
2. Establish a skin of metal.
3. screwed into the anchor.

This method allows you to quickly get rid of the squeak, but it is considered to be quite time consuming and expensive, as the cost of one anchor is about 10-15 rubles.To eliminate the squeak in the same room must be installed no less than 200 pieces!

plywood Stacking

an affirmative answer to the question "Why creaking wooden floor," many masters of laying wooden floors meet, to get rid of the creaking, can be laid on top of the base sheet of plywood.plywood thickness should be 12 mm.The sheets desirably laid at an angle towards the main stacking boards.

But to say with confidence that, after such repair the creaking never come back, can not, and here's what it will disappear for a long time - this is true.

floors tightens screws

One of the most effective ways to combat creaking floor boards is tightening screws.This method is effective if the creaking arises as a result of friction with the board Lagoi.

In this case it is considered problematic to find a place where there is a lag, as well as to determine whether it is not held under the defective board any communication.

All work to eliminate the squeak is what is needed in several areas to fasten two or three screws.

Work Plan:

1. The work is performed by an electric drill.

2. On one side of the damaged plank floorboard hole is drilled through to get to the logs.

3. In the hole insert a nail or screw (by the way, the nails are considered to be more practical).

4. It is necessary to consider the size of the cap, because it must be completely recessed into the board.

screed

works on the floor screed is also called "bulkhead" and refers to the time-consuming process to eliminate squeaking.In addition, along with the fact that time-consuming process, it is considered a low-cost."Bulkhead" - is not nothing but a complete revision of the status of the floorboard and lag.Once a defect is detected, a decision is made, how it will be eliminated.

effectiveness of this method is that during the inspection must be replaced without exception, nails and screws, so the method is also called the floor screed.

When the nail sits in the wood tightly, then squeak does not arise, but as soon as the metal starts to become loose in the wood, rust - there is play and as a consequence - a distinctive sound.

If you replace the old nails on new or set screws - problem disappears.

Non-Proliferation methods

addition to the above methods, the creaking wooden floors can be avoided because:

1. In the formed gap between boards or between the wall and the board is filled with wood chips, and lubricate them with a special sealant for woodgrounds.As part of the sealant, in addition to the lacquer and paint present shredded wood chips, which will fill the space of the gap.
2. Using ropes made of synthetic materials and PVA glue fills the space between the boards and the gap itself is directly coated with a thin layer of putty mixture, which you can prepare yourself.For this taken part powdered sawdust mixed with glue PVA.Additionally, small sized gaps can be filled with wood wax.

When one squeaks floorboards creak eliminate follows:

1. Prepare required accessories: wood sawdust, nails, sex paint, drill, hammer and nail puller.
2. identify problem floorboard and drill a small hole with a drill.Make sure that the drill has entered into a tree deeply and reach the concrete base.
3. Hammer a nail or screwdriver, screw the screw so that the hat was drowned.
4. can not leave on the surface of the wooden floor of the cap, because it can damage the coating and become dangerous to use.
5. Check your work - walk on the floorboard.If it squeaks - screw one screw or hammer a nail, but only from the opposite end of the board.
6. If creaking floorboards a few, you should do the same for damaged boards.But do not forget that if a large portion of the cover is damaged, then this method will not be considered effective.

This video will allow you to learn more about sex defects, due to which there is a creaking, as well as how to get rid of the unpleasant sound: