Cleaning of sewer pipes

Cleaning using scrap materials

cope with clogged drain, with virtually no material costs, it is possible using the available domestic remedies that everyone has.To do this, use a plunger and baking soda and work in the following sequence:

• necessary to remove debris from the drain hole, pour into it a liter of boiling water and wait 15 minutes.
• With the plunger clean
• system then fill in the hole a glass of soda and pour three cups of boiling water.

Soda, forming an alkaline environment, helps to effectively clean the pipes of accumulated debris and deposits on the walls.In addition to cleaning, it performs and disinfection system that helps prevent active growth of microorganisms and bacteria.If necessary, the procedure is repeated several times to obtain the desired effect.

Cleaning of sewer pipes is carried out by another method, which enhances the function of the soda vinegar:

• Half a cup of soda is poured into a drain hole and pour the same amount of vinegar.
• drain system stoppered and left to stand for two hours.This will allow the vinegar and baking soda react and destroy all
• clogging pipes are rinsed with some of the boiling water, then clean water
  In view of the fact that both substances are chemically active cleaning is done at a very high level, and split all types of deposits.Next
  combination of means for cleaning - soda and salt.
• Half a cup of salt mixed with half a cup of baking soda and pour in the drain hole
• close it with a lid and wait 8-10 hours.It is best to leave the sewers in this state overnight to prevent the interruption of the reaction components with the contamination.

To avoid clogging the network is necessary every 2-3 weeks to carry out preventive measures - to shed a few liters of hot water system.This will ensure that the walls of the pipes clean up the layer of fat and soap deposits.

Another means of preventing a vehicle whose composition is as follows: a glass of salt, a cup of baking soda and a quarter cup of cream of tartar.The mixture is poured into the sink, fill with boiling water, then washed with pure water.

The use of chemical agents

On the market today there are many different tools to remove blockages.Cleaning of sewer pipes using them very effectively carried out, for the specific case you can pick up any chemical cleaner - from powder.Completing various liquids and gels.

In order to accelerate the process of cleaning, you must wait the specified time in the instructions, and then use the plunger to allow the passage of undissolved contaminants below the pipes.

Using special tools

simplest and most effective tool in the fight against clogged a plunger.With it you can remove blockages from sinks, baths and toilets, as affecting the garbage and destroying it, it also creates pressure, and pushes the blockage in the pipeline.

Procedure for eliminating blockages plunger:

1. overflow tightly closed to avoid pressure loss created by the plunger
2. Plunger set rubber part on the drain hole.By eliminating the obstruction, it is necessary to control the water level, which should not drop lower than the rubber valve.
3. moving the plunger handle steadily, do not tear off the rubber part of the drain
4. Very clean plunger and rinse system.If necessary, repeat.

If you remove the blockage using a plunger is not possible, and its center is located far from the drain hole, cleaning of sewer pipe by means of a cable.It is designed as a long flexible wire twisted into a spring.Depending on the nature of the obstruction, different nozzles are used.

Before you start cleaning, make sure the cable performance: check its integrity, attachment, etc.

instruction execution process:.

• recommended to remove the trap, then lower end of the cable into the drain hole and take a special pen
hand
• rotate the cable, you need a little effort to push it deeper into the pipe, but you should do it carefully so as not to damage neither the tools nor the wall of the pipe
  

  to rope served longer working with clogging, it is necessary to rotate the handle purely clockwisedirection to prevent deformation of the spring, which can dissolve.

• At the end of the collision with the cable plugged, you need to increase the frequency of its rotation, with the possibility to hook hook debris and pull out
• If contamination eliminated, must be washed with hot water system.Constantly increasing its supply.
• When emptying the sanitary appliance, the water forms a funnel - the operation was successful

.

If the rope stuck in the pipeline, you need to slowly rotate it in different directions, is not an obstacle will be overcome.

Usually, these methods help to cleanse the system and resume its normal operation.But if the cleaning of sewer pipe failed, it is necessary to address to experts.There are powerful machines for cleaning mechanical and hydraulic pipes which are an order of magnitude more efficient and eliminates any type of clogging.