How to solder copper pipe

Rules soldering

The most important thing to remember is that a spike occurs pipes so that the sleeve or socket collect all the necessary details.The formula is as follows: the tube is inserted into the sleeve and her 2 soldered joint.This can also be accomplished by inserting the smooth end into the socket of the first pipe and the second solder.This variant is even more suitable than others.

The following photo clearly shows how the spike, and align joints.

Procedure:

1. docking place is important to degrease all kinds of detergents and alcohol-based agents to clean the interior and exterior of the pipe.Doing this action enhances the adhesion of adhesions.
2. During mount the pipe into the socket or sleeve joint must be selected.
3. Before soldering, it is necessary to include a burner, heat the wire and this heated weight to fix the joint.The principle is very simple: to seal the seam connecting layer of the liquefied solder.

After the solder cools in the docking seam and forms a hard crust and metal, which seals and locks the place spikes.

practice more important than theory or how to solder copper pipe correctly

Hard in theory, but in practice even harder.The critical mass of questions and inconsistencies occur, even in the early stages.Therefore, following a number of practical recommendations.

Planning.During the preparation

Installation Tools:

• Expander for pipes and caliber.Apply to convert the profile after cutting and placing the bell on the end.
• Iron hammer, meter and marker for marking of all components.
• device for sanding work on metal and emery sheets.Needed for cleaning and polishing their end.
• Device for cutting copper pipes and Flat skimmers.To generate the necessary pieces and chamfering.
• course a soldering iron and solder!

When you have this set of young technology, you can start processing connections docking.

How is docked?

Installation involves spike in the socket of the joint.There is using a smooth end.

On a personal experience you have to see about this picture.

now describe how to solder copper trubydalee.

1. First you need to cut a couple of dimensional segments.The most convenient way to do this is not a hacksaw, a special pipe cutter, which is capable of soft copper is expanded.At the same time it can make perfectly straight cuts of perpendicular.
2. then need using sandpaper and wire brush wipe the internal and external working parties.
3. necessary to expand the ends using a gauge or a mechanical extender, which was mentioned earlier.When the socket is formed, it is possible to check the readiness of one simple way, simply enter attachable pipe in the extended area and chamfering.
4. again to clear brush and degrease the working parties to increase the adhesion of soldering.

How to solder copper pipe with joints?

soldering joints involves working with a soldering iron and solder.Preferably use a separate flux and solder, which can improve the quality of the soldering process to build a simple application.

Spike splice occurs thereby:

1. Apply a layer of liquid flux, after which the pipe cleverly inserted into the socket and twist in diameter.
2. place of intensive work necessary to process gas or gasoline burner.Indications required temperature determined by the color of flux, which, if it became dark, then is ready to work with solders.
3. final movement will be an introduction to the opening of the gas burner of the wire solder to the extent that it becomes very soft.You can then wire to stick to the joint and gradually krutnut solder around the pipe, so that the joint cranked.Keep in mind that the solder will melt, if the burner is working, so it should be turned off.

Therefore, the gap between them will be filled and sealed.The device is ready for use.

see below an example of how to solder properly.

How to solder copper pipe anyway?

If familiarization with traditional soldering you are not impressed, and impressed so much that decided to find another way, the further a few others, but also the right choices adhesions.

simple solution - a compression sleeve for the IPA.

When using compression coupling assembly joints is carried out initially by protecting and degreasing end portion, then the clutch disassembly, screwing clamping nut and then screwing it on the tube and the last room in the coupling socket.On the interface wearing a special ring seal, which compresses the connecting seam, and tighten the screws.

installation method is very reminiscent of the connection pipes izplastika in living conditions, and is therefore simple assembly method.But if we talk about the strength and durability, such a connection is not a guarantee joint tightness and sooner or later it will need to be repaired.