Seam roof with his hands

Deciding on self-build homes in the current economic climate is akin to a feat.Sometimes the box to put itself at home is much easier and cheaper than to build it on the roof.It is connected not only with complexity and danger of the roofing, but also to the cost of materials for roofing.With the construction of the house now and then we do our best to reduce the cost of materials.Sometimes this is the only way to complete the construction.If you make a choice on the standing seam roof, then this can be done quite successfully.Seam roof with his hands can be created simply and cheaply.The quality of such a roof is no worse than made from more expensive metal.

What is the folded roof

When using seam technology as a roofing material may be a sheet metal or plastic.The sheets themselves are flat, but their edges are mounting, which are called seams.With these adjacent sheets are bonded to each other without forming a liquid-pervious seal.The edges of the sheets are rolled in a special way.This can be done in several ways, but the most convenient to carry out the process using electric machines, designed specifically for this purpose.These devices greatly simplifies and accelerates the process of folding sheet metal.

cost of such a roof is slightly lower than the finished sheet materials.If you plan to make a seam roof and did roll or sheet metal, not pre-prepared for this purpose, the cost will drop even more.

construction metal roof standing seam method

One of the main advantages of this type of roofing is that it can be collected not only on a solid basis, but also on the sparse crate.However, in this case it is necessary to do truss system very carefully, as if expecting to step rafters.Ideally they should be located so that the fold was below each bar rafter.Otherwise, a situation arises that under the influence of countervailing loads of snow in the winter sheets diverge as a result of the deflections.This will lead to metal corrosion and moisture in the attic floor and roof system.This ill-conceived roof will not last for long enough.Thus, we can formulate the following rule.If you decide to make your own seam roof, then the calculation of the distance between the rafter treat with due care.It should not be more than the width of the sheet metal in view of the lock seam.For continuous lathing is usually not possible to observe.

installation Advantages of standing seam roofing roll metal

From ancient times, seam roof constructed from a single sheet metal of a certain length.Leaf length was less than the length of the roof.For this reason, we do not have to only longitudinal but also transversal folds.This approach is becoming less and less popular.After all, a large number of seams requires a precise arrangement of crates and a special approach to the vapor barrier.Condensation under the metal to anything good does not.

more advanced approach - is the construction of standing seam roofing roll metal.Sheets from the roll are cut long enough to completely close the ramp along the entire length without cross-joints.The longitudinal seams have very high strength and excellent quality.They almost never disagree, even under the very large mass of snow.

Advantages of standing seam roofing roll material lies in the fact that:

• In this case, can be used not only galvanized steel, and metal coated with a polymer coating.This improves the quality of anti-corrosion roof, allowing it to operate for decades without a change not only of consumer qualities, but also appearance.
• Round metal is much more flexible than the sheets.This makes it possible to carry out assembly of the double seam.Metal roll has high strength and integrity that it rules out the penetration by moisture.
• When steep slopes of the roof of rolled metal is much easier to use and safer.After all, you can just roll to roll without risking every time life and health as when laying the sheets on

separately In addition, work on the machine twist folds much easier to roll metal.Indeed, in this case it is necessary to tighten only the longitudinal seams, but do not mess with the horizontal after each sheet.

What tools will be required for the installation of standing seam roofing

particular importance in the production of works on creation of standing seam roofing is playing the correct tool selection.This applies in particular to devices for spin standing seam welds.Such clamping devices, there are two types: mechanical and electrical.In the first case the seams are clamped by means of two frames.With the help of the first frame in the main fold twist, and with the help of the second frame at her screwed matched metal sheet and clamped to form a seam.

use of electric cars at times easier to work.During the first pass, it twists the main single seam, and for the second completely finishes work, creating a complete seal.The second rolling in the reverse direction.This further speeds up the work, as there is no need to go back to the top of the roof.

Besides machines for a spin you need to prepare some more tools:

• Several metal hammer with a flat and a rounded head and a conventional pliers.
• Shears for metal.
• sufficiently powerful drill.
• extension of electricity supply not less than 30 meters in length.
• screwdriver or an appropriate nozzle on the drill.However, the first option is more convenient, thanks to its light weight.
• Measuring devices.

All tools should be safe and not slippery, as having escaped from the hands, it will fall down, which will not only create discomfort, but also may cause harm to third parties.

main stages of production work

primarily for installation standing seam roofing is necessary to determine the type of crates.If you make it a solid, the special calculation is required.Otherwise, it is necessary to determine with great precision step rafters.Crate itself can be made not only of the boards.Its creation should be fine bars, metal profiles or profiled tube.The main thing is that the surface of the resulting crates had no potholes and depressions.Its maximum smoothness - a guarantee of beautiful appearance and reliability of the roof.

On crate stacked on top of the vapor barrier.Material must be selected so that it is light and durable, but at the same time, well protected against rust and well ventilated.Wooden crate requires a thorough impregnation which will protect the wood from rotting and make it susceptible to bad fire.Well treated purlins and rafters provide a lifetime of standing seam roofing is not less than 50 years.The distance between adjacent joists should not exceed 40 cm.

Installation of the first leaves begin to skate.When using a sheet material, the roof sheets are fed a strictly one, as casually pulled off the roof sheet is a deadly weapon for those who at this point may be on the path of its movement.You should also pay attention to the fact that the batten is required to mount the cornice in advance.The same applies to the support bracket on the ridge.When mounting a hip roof, this strap is placed at the site of the stack.

To give a more beautiful and symmetrical type of roof, at first precisely mounted farthest leaves on both sides of the roof.They can be cut very carefully, if necessary.When cutting this region need to be sure to wrap the outside.Businesses these parts are treated with sealant to prevent corrosion, although it is not mandatory.

Subsequent sheets are placed overlap, which must be at least 40 mm.Orient with the overhang on the bottom sheet.When working with the eaves or ridge, each sheet is attached to both the upper and the lower bar on the crate.Hermetically sealed cavities along the ridge and ends allows the use of battens which are fixed by means of screws, equipped with rubber gaskets.This technology allows you to ensure their sustainability in service for many years, since its rubber elastic forces does not allow self-tapping screws become loose.If the roof is planned device snow barriers or bridges, it is necessary to fix them strictly at the joints sheets.

installation features "body kit»

When installing the body kit of the roof Observe the following:

• Prior to installation of roofing required by a spirit level to check the evenness of the ridge and ribs crates.They must be perfectly straight.Cornice overhang which is at the bottom must also be perfectly straight.
• Fixing moldings made in the first place before the installation of sheets.Consequently, the holders are attached earlier to the eaves board for gutters gutter system.
• After the eaves to the crate, attach the valley, closing their bases of quality edged boards.
• On rafters laid a solid plastic wrap or a special vapor barrier material, which is designed to protect the wood from moisture.

Also self made standing seam roof, there are ready-made sheets with a curved edge is required.This is a professional seam roofing.To install it, you only need to hoist the sheets to the crate and hold them, as required by the instruction.

some nuances when laying the finished seam roof

careful measurement rays is required before the process of standing seam roofing installation.If they are straight, they should be equal to the diagonal length.Mounting a bottom seal is always directed toward the start of work.For this reason, some will need to roll out the sheets.The sheets must always be laid from bottom to top.At the length of the slope more than 6 m, it is an obligatory component.This is due to the complexity of transporting top sheets or rolls in the case of a very long ramp.The pediment on the roof is attached so that it is completely closed seam.It is also mounted on the screws for roofing with rubber gaskets.

Skate for standing seam metal roof can be of different types.For a flat roof, you can use a flat horse, and for his cool better shaped variety.Screwed it takes to roofing screws, especially at an angle greater than 25 degrees.The joints of steel roofing sheet with walls or other structures on the roof arrange a rubber or plastic strip, which provides reliable protection against moisture.

Separate device seam roof thing quite time-consuming, but feasible.If we take into account the cost savings, which gives the appearance of the roof, then this option should be considered.