Interior finishing bath with his hands

Today, traditional Russian sauna is gradually transformed.People began to pay more attention to comfort and aesthetic side of the issue.Therefore, great importance has come to play an interior created in this kind of environment.Given that modern baths consist, as a minimum, the steam room, washroom and lounges, you must know which of these facilities use one or the other finishing material.Today, the sale of a large number of suitable materials, which will fit to was made interior baths with their own hands.

How to choose the right material for decoration bath

bath it is subject to a very specific microclimate.It is characterized by high humidity and high temperatures.To heat a long time maintained and used effectively, it is necessary to space heating scheme has been strictly defined.Therefore, the choice of material should comply with the following important principles:

• Whatever was not a high temperature in the steam room, no detail of the interior decoration and does not give off toxic substances, phenols or conventional resins.This principle of sustainability is one of the most decisive in the choice of material for the steam room.
• surface finishing materials and components should not crack or otherwise deform when significant temperature changes and humidity.
• waterproofing properties of the materials must be at a very high level.
• Such wood species like walnut or oak can accumulate and retain heat on its surface due to its high heat capacity.This can lead to the fact that the room is hard to breathe, and in contact with the wood can be burned.Better a wood finish for the pair to avoid, and opt for the larch, aspen and linden.The use of spruce or pine, too, nothing good will not lead, because these rocks emit a lot of pitches, which, moreover, that gets very hot, so also sticks to the body.
• important factor is the need to finish in the bath served as long as possible, but at the same time spending on it were economically feasible.Less than all the rot in the damp environment larch.However, its cost is so high that it finish the whole bath is expensive.But made of larch, for example, a bench or a frame to the shelves quite rationally, as it does not rot for a long time, and buy a few bars of this valuable timber by the forces of each.Sheathe the walls and ceiling can be lime or even a wasp.

However, the different space in the bath differ in their circumstances.In contrast to the steam room, the other rooms are not so demanding of finishing materials.The main thing is to have good antiseptic properties.This can be achieved using modern tools and impregnation.Lounge can be finished with pine paneling, which emits a pleasant odor and are useful for the organism flavonoids.Since the steam to the material the most stringent requirements, consider the process of finishing this building in more detail.

How to make the pair finishing

Steam is the heart of any bath.It is because of her people go to the bath.At the same time, it is in this room, there are the most extreme temperature and humidity indicators.The walls, ceiling and utensils should radiate benefit to humans.Therefore, the selection of useful resins and volatile production - an indispensable condition for a finishing material for the pair.In addition, it should be fairly insensitive to temperature and humidity extremes, as well as well-giving thermal energy.

Wall in the steam room

best to the wall in the bath coat is not the first year after it was built, and after 2 or 3 years.This time it will just be enough for the full structure of the shrinkage.Facing possible to do normal board, but then have to tinker a lot, because each tablet would have to be customized, and even to disguise the nail heads or screws, taking care to protect them from corrosion.Very nice bath may look polbrevna of wood, reminiscent of a block house.However, they cost expensive, and have a greater weight.

rational to finish all the walls of a material such as wall paneling.She has slots for fixing brackets to the wall or furring.Studs or screws are driven and are screwed into the slots that can effectively hide their hats.Despite the fact that siding with the crate can take away from the premises of the area, it is actively used for finishing baths.It is the most convenient for this purpose material.Secure the strap on the walls, even a beginner can.

What is required to be bunk for interior finishing baths

Batten is a thin plank with a certain relief pattern on the work surface, a locking compound on the long ends and ventilation slits on the back surface.For use in the bath, it should be very high quality.Excessively linings capable vspuchilis immediately after the bath to use as dial a lot of moisture.It is for this reason, the material before mounting on the wall is required to withstand day in protoplennoy bath.In contrast, the raw material can be dry when heated in the steam so that excessive gap formed between the slats.

surface products should be smooth, without splinters and knots.No matter what kind of wood is made lining, handle it paints, stains and other chemical compounds invalid because they contain substances may adversely affect the human body at high temperatures.Exceptions are special impregnation based on natural ingredients that are designed specifically for the bath and are able to give the wood a decorative shade and some antiseptic qualities.

How to build a crate in the bath for finishing clapboard

To smoothly and efficiently fix the battens on the walls in the bath, it is necessary to make a crate.To do this, you need to buy or to saw the bars section 30x20 mm.Its fixed at 40 - 50 cm along all the walls with the help of a spirit level.Vertical bars are installed plumb.Krepjat sticks to the walls on the dowels and screws, if the walls are made of light concrete blocks.If they are made of logs or timber, then they can just nail the nails or put on the screws.

Thermal insulation and waterproofing wall surfaces in the bath

insulate the walls in the bath is best to roll with mineral wool insulation.It is especially relevant if the walls are concrete.In order to fix it on the wall, first right over the crates need to fix insulation film, and has attached to it a heater.You will then need installation of waterproofing.In can be used as material for her: aluminum foil or vapor barrier membrane.

Joints waterproofing overlap to make the bars batten and fix a stapler.In the steam room to make thermal insulation is not necessary if the bath wooden wall.The relative position of the slats lining and insulation must provide adequate ventilation under the skin.Otherwise, the fungus may appear there and mold, which sooner or later will destroy all the work.It is important to make an exit pipe insulation through the floor-ceiling non-combustible material.For this is fine brick or special mineral insulators.

sheathe clapboard walls

After Bath insulated, installed waterproofing and crate, proceed to finish the surface of the lining of the walls.This can be done vertically or horizontally.It should be remembered that horizontal arrangement reduces the height of the ceiling boards and may contribute to the accumulation of moisture in the gaps between the slats.Therefore, for the bath still recommended to strengthen the vertical battens.

should start nailing boards lining the far corner of the front door.Due to the specific connection between the slats Lining, such a procedure is the most appropriate, since it provides better appearance in the room.Screws or nails are driven into the grooves so that the hats were hidden.Installation of the first strips must be made very carefully using a plumb to ensure its absolute verticality.Subsequent boards also need to periodically check a plumb, as the deviation of even a millimeter can eventually ruin the whole picture.We will not dwell on the decoration of the ceiling in the bath, as it practically does not differ from the cladding.The only thing you need to pay attention to pipe the output of what has been said before.

Arrangement floor bath

Gender is an important element in interior decoration baths.The quality of it is subject not only to the comfort and appearance of the steam room, and thermal conditions in it.Boards lying on the concrete screed, do not give any effect, because the concrete will be a very long time to warm up, and any draft very quickly will bring heat on the whole not.Making the right start to the floor along with wall insulation or after their complete finish.

To the floor in the bath heats up quickly and well kept warm, you need to create an air layer therein.For this purpose, ordinary plastic may be suitable empty bottles.To tie everything with them, perform the following steps:

• Choose a sufficient number of empty plastic bottles and screw them tight cork.
• Bottles are placed as close as possible to each other on top of the concrete screed.Above them pressed bars of reinforcement, so they do not have surfaced.After this solution is poured all or a mixture of self-leveling, so that the lattice disappeared under the surface together with the bottles.
• After drying of such ties to it can be laid tile or plank.

large amount of air in the screed of the empty bottles will provide excellent insulating properties of the floor.

The second method involves the warming of the floor unit of sand and crushed stone pillows or cushions of expanded clay.Of these materials make layer 10 -15 cm under the thin concrete screed, which provides good thermal insulation.

Finishing the floor finish in the bath can be carried out through the use of tiling or lumber.It can not be used in the bath laminate, since it does not have sufficient resistance to moisture.The use of ceramic tile floor ensures durability, ease of care of them and an attractive appearance.It has a lot of options tiles colors and textures.When using tiles of granite, consider the options for antiskid trapikov or wooden mats.Ceramic tile can be glued directly to the concrete floor.

If the floor is made of timber, we should take care of high-quality processing of boards antiseptic.They should be allowed to use the baths, as there is information on the packaging.Stacked on top of wooden board lag, so that between the screed and boards remained a small gap for the flow of water into the drain hole.Boards must not be laid close to each other, so as always to remain wide gaps up to 10 mm.From moisture, these gaps will become much narrower.You can also nasverlit boards in the holes diameter of 3 - 4 cm. This is enough to ensure unobstructed discharge of water and lack of water stagnation.

Making bath interior

Adopted interior baths done in wooden style.Everything has to embody the natural naturalness and remind of the old days.It is even possible to style the entire room for housing devil or Baba Yaga.If a family has children, they will be happy to go to a bath.

So, for interior finishing baths need to respect the principles of sustainability and high quality waterproofing materials.The interior of the bath should have a rest and to remind fabulous object.And most importantly, in the construction and decoration must comply with all the technology.