How to fix the toilet with his hands - the mechanism of the toilet bowl

Technology does not stand still.More difficult it becomes not only technical devices and assemblies.Modern toilets, in structure and operation, can surprise even skilled plumbers.Yet, despite the various technological improvements, the majority of these plumbing fixtures work on the old, classic lines.So, repair the toilet with their own hands is quite possible and feasible.

understand the toilet device

main components are modern toilet bowl and tank with the release, in which the drainage mechanism.A large number of parts, gaskets makes this mechanism is most vulnerable to breakdowns and malfunctions.Classic flush tank consists of the storage and discharge arrangements.

Savings mechanism

The presence of this device allows you to accumulate a certain amount of liquid for the subsequent draining.The main items here are a shut-off valve and a float.The principle of operation is as follows: in the absence of water, the float goes down.Thus, it acts on the lever and the shut-off valve is opened.Start the water flow.To the extent that, the float rises and gradually closes the valve.Finding the float at the highest point should prevent the entry of water.

drain mechanism

This mechanism removes the accumulated water of life remnants from the toilet bowl.The principle of operation is also simple.Located in the tank opening, closing trap.The tightness this occurs, the less water flows down into the toilet.By pressing the button, the person opens the drain hole, and the water rushes down the drain.

Looking fault

To determine the fault should be several times to pull water from the tank.Since the principle of operation is quite simple, in most cases, cause some failure is immediately visible.

most probable failure mechanism filler

lack of water in the tank.This trouble can arise both because of failure of the tank parts, and because of the contamination of water pipes.To accurately determine the failure need to take some steps:

• Remove the lid from the tank and see how the float falls, if he acts on the valve correctly.You can hand-pick lower the lever.It is possible that the hole something clogged or stuck lever.In some cases, this is enough.
• Then you need to close the valve on the inlet pipe, disconnect the hose from the toilet and open the valve slowly.If the water is gone, then the pipeline and.If water is not available, you should look for blockages in the water-supply pipes.
• bight're set back the tap.If the water flow has not started, it should replace the float mechanism.

If the water inlet hose is not applicable, it is necessary with the help of available items, clean the inlet.

water comes, but does not fill the tank

This fault is corrected by adjusting the float.Suffice lever on which it is installed, a little bend and the leak stops.

When filling the tank is not the shutter is released.This failure requires inspection of the float.If the item does not float, the float should be replaced.If everything is in order, replace the shut-off valve.

Too noisy content

This problem does not require radical solutions.It is only necessary to cut a piece of rubber tubing and a length of about 15 cm. Then, one end attached to the float, the other placed in water.This way you will get rid of uncomfortable sounds.

most probable failure of the drain mechanism

constant water leak from the tank.The most common cause of deterioration is the gasket between the tub and the pipe.

To resolve We perform the following steps:

1. Overrides
2. tap water is removed from the tank
3. Remove the tank itself
4. Install a new gasket
5. Put the tank in place.

In some cases replacement of the float mechanism to eliminate this failure toilet.

There are many different models and modifications of both the toilet and drain devices.The slightest change in the structure does not allow to install the new system in your toilet.Therefore, to buy just such a float or other device, remove it and take with you.

Water does not fall into the toilet when flushed.Starting solution to this problem should be a visual inspection.Sometimes this is due to the blockage.To do this, just need to clean the drain hole.This is easy to do if you have installed a rubber siphon.It is enough to lift it.In more advanced versions toilets require pre unscrew the device.

In other cases, you need to determine how well the membrane siphon rises.Eli does not happen, you should secure it on the arm.It is best to do this can be a conventional wire.

Thanks to this simple knowledge, it is possible to repair the toilet with his hands.Of course, not every failure can be eliminated independently, but many of the problems with the sanitary equipment will be solved.

Video - how to fix the toilet a few minutes