Equipment

August 12, 2017 18:06

Errors washing machine Candy: error codes and malfunctions of machines Kandy e02, e03, e05, e16

Equipment

click fraud protection

Error Codes

Washers with display
Washing machines without display

Frequent faults
failures Tips and Prevention

Machines Candy cope well with washing and encouraging housewivesits small size.A peculiar advantage of this technique can be called and the presence of a code error of the system.Seeing some code on the display, the owner of Candy machine is able to know what happened with the device and what action should be taken first.

Error Codes

Washers with display

code	What does	What happens to the machine	Causes Error	What
E01	problem with locking hatch	door is not locked, and there is no indication buttons.	not work or locking device were to malfunction elektrokontrollera.It is also possible violation of the wiring.	Check blocker hatch and wiring, and then examine elektrokontroller.Repair or replace the non-working parts.
E02	problem with water Gulf	water is not poured into the machine or its level in 210 seconds does not reach the required parameters.Also, this error is displayed at a very high level of water, not allowing to run the command.	valve does not work the bay. elektrokontroller cease to function. clogged strainer Gulf filter system. pressure switch stops working or there was a leak in its nozzles.	Check the status of the valve, pressure switch function and operation of the controller.If necessary, clean the filter in the filler system.
E03	problem with the water draining	water is not drained or discharged from the machines for longer than three minutes.	not working drain pump or in its chains poor contact. has worn pressure switch. drain tract obstruction.	Check pipes and hoses, drainage systems, as well as the pump and the water level sensor.Defective parts replaced workers.
E04	problem with a filling valve	volume of water inside the tank above the required parameters, resulting in a pressure switch signals the overflow tank.	Broke filler valve (it stays open all the time) or damaged elektrokontroller (often at fault "fault" triac).	Check Valve triac and Gulf repairing them or running them part replacement.
E05	problem with hot water	The water is not heated.	not running a temperature sensor elektrokontroller or PETN. faulty program selector motor infringe circuit control unit.	Rate operation of the heater, measure the resistance of the temperature sensor and the motor program selector.Also it is necessary to perform testing circuits and controller performance.Defective parts replaced.
E07	problem with the engine	motor rotates rapidly and dramatically.After three attempts to run at a maximum speed of washing stops.	tacho does not work (most likely the problem lies in its core).	Check winding resistance of the tachometer, and if it is faulty, replace the unit.
E09	problem with the engine	shaft stops rotating.	does not work all the control unit has blown or triac.	Rate job control unit and the state of the triac, and if they are found defective parts, conduct their replacement or repair.

Washing machines without display

models without an error display is determined by the number of flashes of the indicator, which is located on the bottom left:

code (number of flashes)	Whatdenotes	Causes error
light is on constantly	problem with the control module	does not work, the control unit or failure of his program occurred.
1	problem with locking hatch	not work or locking device appeared violation wiring.
2	problem with filling the machine with water	has worn Gulf valve or pressure. Bay hose kinked or dirty. water pressure in the pipes is too low.
3	problem with water draining	not working drain pump or had deteriorated contacts in his chains broken. drain tract obstruction.
4	problem with the valve Bay	valve has worn (not closed). pressure switch is not working or its wiring is broken.
5	problem with the temperature sensor	Sensor has worn due to a short-circuit or break.
6	problem with memory EEPROM	A memory error occurred or not working the control module.
7	problem with the engine	An interlock drive motor. devoured hatch lock (door closed).
8	problem with tachometer	Tachometer come into disrepair due to a short-circuit or break.
9	problem with the drive motor	Blown triac.
12 and 13	communication problem	damage the connections associated with the control module.
14	problem management	not work the control unit or its wiring is broken.
15	problem management	not work the control module or failure of his program occurred.
16	problem with TAN	heater is damaged due to a short circuit. damage the insulation.
17	problem with tachometer	Tachometer sends incorrect signals.
18	problem management	not work the control module or mains supply are not suitable for cars.

Frequent faults

The most common problems that owners of washing machines Candy turn to repairmen are those:

water is not drained from the machine.Most often this is caused by a malfunction of the pump malfunction or clog the drain system.
The device does not turn on or work machine stops at the beginning of the washing process.The reasons for this problem is more, for example, a low voltage on the network is not properly closed door, a problem with the electronics or defective filter.
water does not heat up during the wash.Here you need to look for problems with the temperature sensor, heater, electronic modules or circuits of these units.
Linen is not pressed.The problem may be caused by a clogged hose, engine overheating, breakage tachosensor or excessive load of laundry.
During operation there other sounds, noise and clatter.The reasons are quite diverse - from falling into the tank and small items of linen unbalance in the drum to the weakening of the counterweight or bearing wear fixtures.
during or after washing out of the machine begins to flow water.This occurs when damage to the pump, sunroof seals, inlet or drain hose and tank.
water is not poured into the machine drum due to a blocked filter, pressure switch failure or some other reason.

about Candy washing machine repair E05 error, see the following video.

Tips and prevention of damage

Regularly clean the machine outside, but do not use this tool with solvents, alcohol or abrasive particles.To clean the device is sufficient to use a damp cloth.
Inspect the container of detergent after each wash, removing balances (this will prevent them drying in the container), as well as before each subsequent washing.If necessary, remove the container, rinse under running water and return to the place.
least once in 6 months Inspect and clean the drain Candy machine system.To clean the filter, use the instructions that you find in the instructions to the machine.
If you need to move the car or it will not be used for a long time, all the water should be drained out of the machine.

For long work of your assistants do not forget it clean and carry out preventive measures, told in the Ukrainian program "All bude good."

instagram viewer

Build Daily