Anti-slip tiles on your security guard

-slip tiles - where there was a necessity?

With the advent of ceramic tiles, many appreciated its advantages, especially in terms of operation.She quickly laid, easy to clean, it outwardly looks very solid, it can be issued even business premises.Because of its resistance to moisture, the use of such coverage found in showers, basins and other richly moistened areas.

But because of the smooth surface to walk on a wet tile dangerous (for example, in the pool).And coming after the rain in a room with tiles, each just once, but slipped.This has prompted a search for new solutions, so there was a non-slip tiles.

It was created in two stages: first came up to do a special embossed pattern on the tiles, and then began to use new materials, which themselves possess anti-slip properties, such as granite.

This useful feature tile regained when it created many serifs, drawings, coated, made a matte texture.This all contributed to the increase of friction and removal of the excess water, without prejudice to the people passing by.

choosing future coverage, you need to consider many factors: cross-premises, the slope surface, as you will walk on the floor.The offer on the market today, enough, there are many classifications of rooms and tiles for them, so you should look into this in more detail.

Anti-slip tiles - on any markings to look for when choosing?

slip tile has several classifications , which help to navigate in a variety of coating and accurately select the corresponding space safety:

• by volume on the tile profiles;
• for slip resistance;
• the type of premises where high humidity, and go barefoot.

In accordance with a first classification mark looks like «Vx», where instead of «x» put a figure that shows an antislip profile ratio of volume to surface area of ​​the tile element, measured in cm3 / dm2.At the very first class V4, this ratio is equal to 4 cm 3 / dm 2, at the latest - 10 cm 3 / dm 2.

second classification reflects the stability of the room depending on the angle of the surface.In total there are 5 classes and they are labeled as the «Rx», where «x» - this is the class number, which is associated with an angle of inclination of the floor.R9 - the very first group of surfaces, where the angle of the smallest and is 3-10 degrees.The coolest surface corresponds to the class R13, and the angle is more than 35 degrees.

latter group includes facilities such as swimming pools, showers, saunas, and other "water" places where people often move barefoot.Some elements of these places are grouped in danger of falling, and hence the class tiles, which makes them safer.Marking Easy "class A", of which there are three - A, B, C.

The first corresponds to the places where the tilt angle may be 12-18 degrees, as a rule, this locker room, where wet, but the water is still not flowing under their feet.The second class (B) correspond to the showers, and the angle of the slope on which the tiles will not give you the slip, is 18-24 degrees.The last class - this is the most anti-slip tiles, it can keep you on an incline greater than 24 degrees, and the place where you need a clutch, it is the pool steps.

anti-slip tiles - a few words about laying

to the surface requirements and installation does not change the type of tiles, there are only some of the features.Floor tile slip also has these details.The initial phase of work is unchanged: surface need dry, smooth and free of dust, dirt, old tiles and old adhesive.

Then select adhesive and grout.Considering humidity premises, and in some cases even overt presence of water, these components demands are quite clear.And grouting vary by room type, so when choosing it's worth considering.

A selection of the type of adhesive depends on the type of tiles, porcelain tiles will be laid if, this material requires a high adhesion adhesive (not less than 28 kg / cm2) because it falls off from the normal.It's all about water absorption porcelain tiles, it had extremely low, so the bonding mechanism is slightly more complicated.

adhesive is applied all at once, and then evenly distributed over the surface, then on its surface create hollows notched trowel.Now you can lay tile.This should be done gently, so as not to extrude the adhesive to the surface layer must remain the same thickness and the same flat.Sutures made of the same thickness, so as not to have spread, inserted spacers-crosses between them.

Then use grout, tile cleared of traces of glue is left to dry and harden.Walk on the floor it is desirable to only 4 days.