Universal bench for the masters of all trades

The versatile workbench different from the usual?

most universal, perhaps, it is considered the furniture-transformer, which is able to transform and change their destination in a matter of seconds.For example, a table, a chest of drawers, chair, bed, wardrobe-room (the latter option is not a joke, have a job in the cabinet is quite possible).However, when it comes to the bench, everything is much easier, since it is sufficient that the working surface could be used to work with different materials.

In particular, for working with wood, you can adjust any table, the soft material is easy to process, and reliable emphasis is not always necessary.But it is necessary to take up a metal billet, and everything changes - we need a vice, files that need to lean all the weight, hammers, which are almost not deform the material is not inferior to them in terms of hardness.For such work you need a really strong and reliable universal workbench.

It differs from the Workbench is the strength of the frame, which is often made of metal.

ideal workplace is considered that, on a work surface that can even install a small anvil, without prejudice to design.However, despite the rigidity of the frame table-bench is not necessarily to be fixed.You can choose the mobile version of sliding on the base of strong skaters, or folding.

universal workbench for balconies

easiest way to buy a ready table for the woodwork and plumbing work, but folding options are extremely unstable, and the housing is quite expensive, so let's combine both types in the construction of its own production.Permanent location for the bench becomes a loggia, a foundation - built-in wardrobe of two, three or four compartments (depending on the width of the balcony).

We need the closest to the wall section at the bottom of reimplemented it firmly fixed wooden shield (if there is a bottom compartment with a door, replace door).Next, get rid of the doors in the upper compartment, if it is part of a broad bay, vertical board divide it into two parts, parietal should look like a niche.Positioning for example, the cabinet on the left when facing the wall between the balcony and the living quarters.

basis of the bench will be the frame of the timber section of at least 10x10 centimeters.It is possible to make rectangular or larger left and right narrow part, i.e., an L-shaped.The second option is preferable, if you need to set the front vise.On the left side of the frame cross member 10 is mounted in centimeters from front and rear ends of the beams, so that two protruded outside the cube frame.They drill-holes with a common axis, they will pass through a metal pipe, rigidly fixed to the bottom of the recess - this is the hinge to the cabinet retractable bench.

top of plank boards and firmly fastened with screws to the board width of 60 cm (in general, the workbench area depends on the width and height of the niche, and must be a little less of it).Along the back edge of the table top (which is attached with screws vertical shield in the presence of the window wall) do a notch tools, along the front edge of the cut out a rectangular hole 3x2 cm under the locking wedges and stops with overhead projections corresponding form at the bottom.The step between the holes - 2 or 3 centimeters.

to the bottom surface of the right cross beam of the frame fasten U-shaped profile, and the floor and wall mount rack is rigidly desired height of the board corresponding to the width of the narrow part of the bench.Now, if you omit the table top in the working position, the profile will be on the upper edge of the support, ensuring a secure fit.Between racks and cabinets set the bar fixed to the first wedge connection, and the second - with the help of metal brackets and transverse axis.

remains at the top of the niche set rising straight up hinged horizontal bar, put on emphasis in the opposite wall, which is in the lowered position will keep tucked away in a niche bench.If space permits in the compartment, the side of the table top can be screwed one more gripe end.

Making woodwork and metalwork table-transformer

as a basis for the workplace, able to withstand locksmithing work, it is best to use the metal frame from the school desk or manually brewed his likeness .The drill hole profiles for full lining of the metal wood paneling, and then move on to the "second part Marlezonskogo Ballet" - namely, the production of a tool box.Some may ask, what's the workbench, but remember that we do table-transformer.

design feature is the versatility of the universal workbench, including some of its units can be used as storage for tools and workpieces.

So, facing the side frame and rear walls made ahead of doing the door, to maximize interior space frame.The upper part of the bench will be divided into several cells box dimensions corresponding base and its side walls should be lower than the bottom, and the distance between the downwardly projecting planes should be slightly greater than the width of a base.

When the sidewalls should be twice as long as necessary, stepping forward, they will lay down cover, twice as high as for the box area, it will be an excellent countertop for minor works.At the same ridges can be laid verstachnuju board, so access to the tool kit will be absolutely free with raised hinged lid-top.