Why washing machine taps for washing and spinning , and what to do when knock

Yesterday MachineIt worked flawlessly, but now out of it came the loud knock?Do not rush to get upset and call a repair shop.Perhaps it's not so serious.To start

listen: if disturbing noises caused by the large plastic buttons, metal buttons, and other hard parts of clothing, strikes the drum in rotation.If the cause is found, the next time before you load the laundry, turn it inside out or put into a special bag.

contents of the drum at anything?Then proceed without delay to look for the causes of the problem.

Before inspection, unplug the appliance and turn off the water supply. Examining the equipment in search of the cause of the malfunction, please note the following points:

uneven distribution of the content is typical for older models of laundry equipment.Underwear in such devices is dumped in someone.This causes an imbalance - and the drum during each revolution hits the body of the machine.To resolve the problem, stop the work of the technical means and align the contents of the drum by hand.The new models such disadvantage is eliminated.

Make sure that the machine is set up properly, it will help level the building, which is placed on the housing cover.Another way of testing - an attempt to shake the device: if the installation is carried out according to the rules, the design did not stir.

In cases when the vehicle has an uneven surface, adjust the balance using the stand made of silicone, which are now sold in any specialty store.

In modern washing machines elimination system imbalance is based on the work of the springs and shock absorbers, to which is attached the tank.With their help, the vibration is compensated, and the balance is adjustable.Over the years these parts lose their elasticity, wear and, consequently, damaged.Often, their failure is the cause knocking.

manifestation of such a failure would be offset or unusual tank tilt, resulting in startup, he will strike the other internal parts of the device.In this case, immediately interrupt the washing process and eliminate damage, dismantling the machine and replacing the defective parts.Along the way, check the condition of the shock absorber mountings and tighten them if necessary.

Dampers stretched so much that touch the bottom of the tank wall, thus creating a knock?They also require immediate replacement.Even if the status of one of them is not satisfactory, change will have both at once.Otherwise, the load will be unevenly distributed.As a self-

replace shock absorbers, see the following video tutorial.

order during washing if it is wet and heavy with linens did not violate the balance of the technical means to the bottom or top of the tank is attached counterweight - concrete load, making this part more severe, and the car - a stable.

If during the spin cycle the device rattles and vibrates, reassess the counterweight.Over time, the attachment on which the cargo holds, weaken, and he begins to hang out with a bang hitting the tank.To resolve this problem, the machine will have to be dismantled and tighten the fixing bolts.Sometimes it is found that the counterweight is damaged, then it must be replaced.Difficulties with the acquisition of replacement part does not arise.Attach the new cargo to the tank, collect the car - and start washing.

drum knock usually caused by three reasons:

• The tank was small object which during rotation of the drum beats.The danger of this problem is that the drum may jam.It is necessary to interrupt the operation of the process and remove from the tank all the excess.To do this, remove the front or rear wall of the body (which is - depending on your washing equipment models);remove the heater and through the opening to remove the garbage.
• If during the spin cycle knock preceded creaking cause of the problem lies in bearing wear.This part of the design you want to replace.Usually these problems are associated with long-term technical tool life.Professional repairmen warn that the removal of such a malfunction requires replacement of all bearings and seals, since the failure of one element can indicate deterioration of the whole system.
• reason could be knocking power strip attached to the rear wall of the body (its main function - protecting the machine from power surges).In operation, the screws on which it rests, weaken, and the filter begins to touch other parts of the device.In this case, the item should be secured firmly, replacing the weakened fixing if necessary.

Remember that when a knocking or other extraneous sounds operation of the machine should be interrupted as loose and damaged parts can cause a running mechanism of serious damage.