How to put the plastic panels

In which room is best to use plastic on the walls

plastic panels technically can be used in all the rooms, but they will look harmonious only in such areas as a hallway, kitchen, bathroom, toilet.Most often used for lining walls and ceilings of the last two points.This distinction is due to the high resistance of this material to moisture.

How to decorate a bathroom using plastic panels

Before you begin to work on the installation of plastic on the bathroom wall, you need to stock up on tools:

• drill;
• level;
• screwdriver;
• mounting a stapler;
• pliers;
• ruler or tape measure.

also be needed in the following materials:

• plastic panels;
• fixing material;
• wooden slats;
• metal holders;
• fillet;
• plastic holders;
• docking moldings.

Step 1: Installation of a wooden frame

This step is simple, and will have to afford to any host.To work fit wooden slats about 20 mm thick, which are attached to the wall using screws in increments of 50-70 cm should first fix the vertical rails, and then -. Horizontal.An important condition that must be met in the process is to install horizontal slats strictly on the level.In places intended placement of furniture and decoration of wall mounting possible additional brackets to reinforce the structure.

Step 2. Attaching the panels to the frame

Plastic elements are attached to the pre-prepared skeleton using metal brackets, which are first inserted into the groove of the panel, and then attached to the rails by means of nails or screws.Because plastic straps are mounted on frame one by one.

Step 3. Finishing work

In corners it is necessary to fasten sheets of lining using corner moldings, and at the end of construction - with the help of finishing.Next, do not be amiss to check the evenness of the surface structure and manually to verify the reliability of the fixtures.

How to make the panel under the bath made of plastic with their hands

Sheathing space under the bathroom with the help of plastic is one of the most common ways to create a bathroom panels, along with a covering materials such as drywall, tile, brick, fiberboard or particleboard.Plastic does not deteriorate from exposure to moisture, so the finishing material is best suited for bathrooms.

Before you begin the installation of the panel under the bath, you need to pay attention to several workers nuances:

• When creating blind plastic screen should definitely leave the technical opening of the door or hatch to when repairs can be easily obtainedaccess to communications pipe.
• lower part of the plastic panel, which is in contact with the floor to be treated with an insulating material (such as silicone liquid) in order to provide space for the distinction with the rest of the space bath room.
• It should be remembered that the plastic fence under the bathroom does not perform functions of the support structure, so bath should not rely on it.

in the creation of the screen under the bath will need these tools and materials:

• plastic lining;
• metal profile;
• mounting adhesive;
• liquid silicone;
• hacksaw with small teeth;
• simple pencil line.

Consider the steps how to make a plastic panel under the bath with his hands.

Step 1. Construction of metal framework

As is the case with fastening lining the walls, if the construction of the screen under the bath of plastic panels are mounted on the frame.Only this time, the carcass material will be a metal profile.Straps are attached to the upper profile board bath and the walls.The lower part of the frame, as indicated above, to be glued to the floor with a liquid silicone.

Step 2. Preparation of plastic panels

panel layout is applied, the corresponding size of the frame.Then plastic with a hacksaw to be cut into pieces of the desired size.

Step 3. Installation of lining on the prepared base

prepared panel infest the profile grooves and fixed with assembly adhesive or liquid nails.At the corners of the corner moldings are used, and the bottom panel - finishing.

Step 4. Finishing work

After the attachment lining on the frame is necessary to equip the access hatch under the bath.To do this in a thoughtful place to cut a hole into which is inserted into the door or hatch.Work on the panel under the bath is finished.

Lining has become a real budget alternative to the classical solution for bathrooms - tile.For the bathroom, decorated with plastic, easy to care for and serve such a coating for a long time.