As polypropylene pipes without soldering soldering iron

As soldering polypropylene without soldering

Question soldering polypropylene pipes today is acute for each host its kvartiry.Ved without exception, want a quality fastening pipes, because it affects directly:

• life of water or heating system,
• the need for the repair costs.

Therefore, many are wondering how to solder the pipe to avoid further trouble.

For soldering pipes made of polypropylene required, of course, a special soldering iron.But what if the house is not such a tool?The answer is simple: use the materials at hand and instruments.For example, a gas burner.

Undoubtedly, every home should be a gas burner.But if it does not, the choice of this instrument should take into account its main parameters:

• used gas;
• cylinder connection.

This soldering method is suitable not only for small-diameter pipes, but also for soldering of large diameter pipes.

With gas burner possible independently to repair or installation of the heating system in a short period of time.

Soldering requires:

• accuracy,
• care,
• commitment to quality,
• preparation for major works.

polypropylene pipes: manual soldering

consider gradually as quality weld tube:

Step 1. Pick up a pipe of suitable diameter.Note that newly acquired pipe must correspond to the diameter of the old.This will help avoid problems when connecting.

Step 2: Measure twice, cut the required length of pipe.Do not forget to add an extra 25 millimeters, which then remain in the fitting fusing.

Step 3. Preheat using the burner tube and fitting.This should be done at the same time.

Step 4. After that, the details need to connect and hold a bit, waiting for them to cool down.

Note: Before installing the pipes is necessary to make a detailed scheme in which they are connected.It should be noted the installation site turning corners, tees and valves.

recommendations for successful work

Consider the tips and tricks that will help carry out the work qualitatively:

• recommended to purchase connecting pieces and pipes predominant one manufacturer.This is an important point, because each manufacturer has its own technology for manufacturing these elements.This means that the melting temperature may vary in details that are not suitable for monolithic structure.
• before the main work items should be cleaned and degreased, in order to avoid violation of the quality of the connection.
• Practice first on the pipe section to know how much effort is required to apply to obtain the expected result.Note: the pipe inserted into the fitting, it is impossible in any case to turn, this will break the bond strength, since the surface of parts will come in waves.
• If you choose quality, not worth saving!Good products will last longer than you will save in the future.
• If the room temperature is lower than + 5 ° C, no need to take risks and start working, because its effectiveness is greatly reduced.The compounds in this case are fragile, and the connecting parts will require additional heating.And it is fraught with unnecessary melting and deformation elements.

Soldering wires: how to solder, soldering iron if not?

I'm sure many have faced the fact that the need to hold together the two wires, but soldering is not at hand.It remains to rely on the ingenuity of his contemporaries, offer an easy way of soldering, which will be mastered by everyone.

on the market today provides such materials:

• solder paste;
• Ribbon soldering.

without soldering solder paste using

Solder paste is called a mechanical mixture of flux, solder powder and the lubricant, ie the binder.

Manufacturers solder pastes are practicing their silver-based production, which makes it possible to use this mixture for brazing different types of nickel, steel and copper alloys.

Requirements for

pastes Solder paste should:

• very quickly flake, but not oxidized;
• be viscous (very important!) And save deformation;
• have adhesive properties;
• laundered in common solvents;
• not drain abroad applied layer;
• not leave indelible residue after application;
• not affect the technical properties of the board.

soldering Stages

Step 1. The primary objective - preparation wires.Clear the wire surface by applying a stationery knife or wire cutters.

Step 2 wires are twisted.

Step 3. Place spikes carefully smear the paste solder.Apply a drop of paste needed across the wire surface uniformly.

Step 4: Position of the warm up.For this may be a conventional cigarette lighter.After heating the paste would represent a solid spike.

Step 5 is put on the wire shrink tube, which also handles the flame so that it is uniformly distributed over the surface of the wire.

Note: This method is suitable mainly for solder bonding wires of small diameter, for example, the wires of the headphones.

solder paste in water supply systems

Surprisingly, solder paste applied in the water supply.These substances have specific requirements:

• The composition of the solder is added silver or copper, and it increases the melting temperature.This makes the alloy mechanically strong and durable.
• not allowed to flux or solder had a total toxic substances, so they do not contain lead or any toxic metals.
• Flux should be easily washed off with water, and in any case does not cause corrosion.

soldering using solder ribbon

Soldering tape - this is the material that is applicable when installing electric wiring, its repair or replacement, in the household and in the field, as well as in the automotive business.

Consider phased soldering process by solder ribbons:

Step 1. With the wire insulation should be removed, that is, clean clippers.

Step 2.Skrutit wire and wrap after twisting ribbon of solder.After removing the protective film side with the flux applied to the wire and compress the surface.

Step 3. Heat place match or lighter winding up until the solder completely will be spread on the surface of the wiring.

Step 4: Wait for cool down, then remove the excess flux.

As you can see, for soldering wires to run to buy a soldering iron is not necessary, you can use the methods described above.This will save both time and money.