Build Daily

Country Houses

August 12, 2017 18:06

Frame pools with their own hands - Construction of frame pools

click fraud protection

pool in a country house - it is an opportunity to plunge into the heat of summer, and a place for kids games.However, the construction of the capital pool is laborious and requires large financial costs.An alternative solution - the device frame pool.

Frame pools with their own hands

Frame pools with their hands

main stages of the construction

frame pool technology of erection of frame pools involves four basic steps:

  • Site preparation;
  • frame assembly;
  • Making foundations of an awning fabric;
  • Mounting pool.

Materials and

tool for basin unit with wooden frame needed:

  1. Awning fabric thickness of 650 g / m2;
  2. Building a hairdryer, temperatures range from 20 to 700 degrees, and the crevice tool on the hair dryer;
  3. beam 50x100 mm, 50x50 mm;
  4. Eaves 25 mm;
  5. if desired - facing materials (eg, Lining);
  6. Screwdriver;
  7. Indelible antiseptics for wood and asphalt mastic;
  8. Eyelets - through metal rings;
  9. galvanized screws with washers, exceeds the diameter of the grommet.

number of materials needed depends on the size of the pool, so it is worth pre-draw the sketch, plan the location of the support members, the number of boards and beams.Do not forget: the water will put pressure on the pool wall, so he did not lose shape, the walls must have sufficient rigidity.

Site preparation

Frame pool can be done both with a deep in the ground, and without it, but in any case must be removed from its place of installation, everything turf, roots, stones and other hard objects.

The platform must be leveled and compacted, then fill river sand.The layer thickness depends on the load and the depth of the pool.On average, 5-10 cm of sand is enough.

Site preparation for frame pools

Site preparation for frame pool

Construction frame

imposed several requirements for the chassis: strength, durability, ease of installation, ease of use.To build a wooden frame can be used-dried pine lumber treated with antiseptic indelible.To strengthen the structural elements necessary to blued (black) self-tapping screws - they do not rust and can withstand considerable static loads.

For device size rectangular pool 3h4,5 meters and a depth of 1 meter will need the support of ten bars of a length of 1.5 meters.The bars on two feet is impregnated with mastic asphalt - this part will be later dug into the ground.The pad mark and half a meter deep pit dug in the corners of the site, as well as on the sides - for intermediate columns.The distance between adjacent pillars is obtained equal to 1.5 meters.Install corner posts, align them plumb, check the diagonal and strengthen them and covered pit gravel, sand and tamped tight.Intermediate poles set is similar to aligning them with the help of a plumb position and strings.

bars along the perimeter fastened by means of an edging board.The amount depends on the height boards basin.Strengthen its better inside the frame in order to reduce the load on the screws.The supporting pillars on the outside need to strengthen the braces from the bar 50x50, setting it at an angle of at least 30 degrees.

Manufacturing bases

pool basis can be made of PVC fabric tent, choosing the color to taste.This fabric is durable, does not pass water and careful operation can serve for years.

awning fabric is placed over the smooth side up and begin to reveal the basics.Thus it is necessary to leave allowances welding seams: seams on the inner 30 mm, along the upper perimeter - 100 mm.

welded elements bases with the help of a hair dryer building, superimposing them on the overlap width allowance, heating the fabric to a light solid melting and laminating roller.After welding, the bottom wall and the upper edge to be treated substrate.By bending the edge of the upper perimeter of 7-10 cm, it boil a hairdryer, and after cooling holes are punched and mounted eyelets in increments of 50 cm.

Basis for frame pools

basis for frame pool

Installation

pool basis is placed into the preparedframe, straighten, raise the edge.Through holes in the grommets to secure the base to the upper edge of the frame with galvanized screws through the wide washer, creating a uniform warp tension.At work it is necessary to use the building level to the top of the pool turned horizontal.

top pool equipped with bumpers for the convenience of the planed boards, covered with a waterproof varnish.The ladder can be installed as metal and wood, not forgetting to be careful - the ladder should not have sharp protruding elements, which can damage the substrate.

outdoor pool side for beauty and convenience, you can sheathe a tree and your pool will be a real masterpiece and site decoration.

Video - installation of the frame pool

instagram viewer